About RugerM77

Basic Information


Age
67
About RugerM77
Location:
Kerikeri
Interests:
Hunting, reloading, scuba
Occupation:
Retailer

Statistics


Total Posts
Total Posts
340
Posts Per Day
0.22
General Information
Last Activity
Yesterday 08:59 AM
Join Date
07-01-2021
Referrals
0

3 Friends

  1. Micky Duck Micky Duck is offline

    Member

    Micky Duck
  2. Sowslayer Sowslayer is offline

    Member

    Sowslayer
  3. tetawa tetawa is offline

    Member

    tetawa
Showing Friends 1 to 3 of 3

435 Likes

  1. RugerM77
    RugerM77 liked post by zimmer On thread : Using comparator tool when seating projectiles.
    With compressed loads my arbor press struggles. Sometimes you can stop or minimise jack out (not jack off) by keeping the press handle down for an extended period. The Sinclair Hex nuts are...
    Liked On: 30-05-2023, 09:57 PM
  2. RugerM77
    RugerM77 liked post by zimmer On thread : Using comparator tool when seating projectiles.
    If you're interested in doing it, very accurately, look at the Alex Wheeler method. https://www.wheeleraccuracy.com/videos Look at his video "Finding your lands". Anyone else who has published...
    Liked On: 30-05-2023, 09:56 PM
  3. RugerM77
    RugerM77 liked post by Bagheera On thread : Using comparator tool when seating projectiles.
    I fiddle with the micrometer seater till the CBTO is what I want then leave it there and load al my rounds. Fortunately I only use one cartridge so can just leave it there. I measure the loaded CBTO...
    Liked On: 30-05-2023, 09:56 PM
  4. RugerM77
    RugerM77 liked post by mudgripz On thread : IMPORTANT ANNOUNCEMENT
    Dan - have never had an issue with your moderation. Not once. As Snap says above - no apology needed. You provide a very useful service - carry on with the good wishes of all. Cheers Mike
    Liked On: 30-05-2023, 02:57 PM
  5. RugerM77
    RugerM77 liked post by dannyb On thread : IMPORTANT ANNOUNCEMENT
    it' ain't worth it bro....you only enjoy it as it takes the heat off you right :yaeh am not durnk:
    Liked On: 29-05-2023, 09:45 PM
  6. RugerM77
    RugerM77 liked post by MB On thread : IMPORTANT ANNOUNCEMENT
    No idea what you're on about, but keep up the good work.
    Liked On: 29-05-2023, 09:44 PM
  7. RugerM77
    RugerM77 liked post by Micky Duck On thread : IMPORTANT ANNOUNCEMENT
    ya calls a spade a spade...dont change mate. you doing a good job...and filling a void that needed filled,moderator response time is at all time low/quickness,which is a great thing when something...
    Liked On: 29-05-2023, 09:44 PM
  8. RugerM77
    RugerM77 liked post by dannyb On thread : IMPORTANT ANNOUNCEMENT
    I would like to take the opportunity to formally extend an apology to the general forum community. I have at times been a little pointed and abrupt about issues that could have been dealt with a...
    Liked On: 29-05-2023, 03:49 PM
  9. RugerM77
    RugerM77 liked post by johnd On thread : Using comparator tool when seating projectiles.
    I have another approach to this. It can also be done prior to sizing. Especially if you are just bumping the shoulder with a bushing die and mandrel. https://youtu.be/02xWd-vBtFM
    Liked On: 29-05-2023, 01:28 PM
  10. RugerM77
    RugerM77 liked post by gqhoon On thread : Using comparator tool when seating projectiles.
    Have a look at the Short Action Customs bullet comparators….the insert matches the leade angle dimensions of your barrel / chamber. So BTO measurements you take relate to where the projectile...
    Liked On: 28-05-2023, 09:27 PM
  11. RugerM77
    RugerM77 liked post by Kiwilad2021 On thread : Using comparator tool when seating projectiles.
    Speaking of graphite powder where is the best place to get some without costing a small fortune? Cheers
    Liked On: 28-05-2023, 03:12 PM
  12. RugerM77
    RugerM77 liked post by 7mmsaum On thread : Using comparator tool when seating projectiles.
    Use cotton buds to wipe graphite powder on the inside of case necks and on projectiles Fingers stay clean then
    Liked On: 28-05-2023, 02:13 PM
  13. RugerM77
    RugerM77 liked post by 7mmsaum On thread : Using comparator tool when seating projectiles.
    Zimmers method is perfect Seat 10 thou too long them measure with the comparator Write that number down if you need to Then adjust the micrometer seating stem down for the last amount ...
    Liked On: 28-05-2023, 01:04 PM
  14. RugerM77
    RugerM77 liked post by Ranger 888 On thread : Minimum pack contents
    We used to run a series of 3 weekend courses, spread out over several months: Basic Bushcraft, which involved the "classroom" content, e.g. first aid, food and cooking, pack contents, tents and...
    Liked On: 26-05-2023, 03:12 PM
  15. RugerM77
    RugerM77 liked post by yeah_na_missed On thread : Minimum pack contents
    Ha ha, I read Tahr and BarrytheHunter's posts fully aware I carry too much and feeling utterly ashamed, so instantly resolved to cull a lot of shit... but then read Ranger888's post - especially the...
    Liked On: 26-05-2023, 08:27 AM
Page 8 of 8 FirstFirst 12345678

02-05-2021


29-04-2021


27-04-2021


10-04-2021


17-01-2021



Page 8 of 8 FirstFirst 12345678
No results to display...
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!