Shelley
Member

400 Likes

Page 10 of 27 First 123456789101112131415161718192021222324 ... Last

• Jump to page:

1. 
   mikee liked post by Shelley On thread : Sharpener edge test

   So my final test was to cut through some rpm thick natural fibre rope, no idea what it was but it came out of a gym, the stuff you used to climb up as a kid then fall onto the hard wood floor...

   Liked On: 11-05-2020, 08:57 PM

2. 
   stevodog liked post by Shelley On thread : Sharpener edge test

   So my final test was to cut through some rpm thick natural fibre rope, no idea what it was but it came out of a gym, the stuff you used to climb up as a kid then fall onto the hard wood floor...

   Liked On: 11-05-2020, 07:37 PM

3. 
   Cordite liked post by Shelley On thread : Sharpener edge test

   Decided I want to compare the edge of some knives that I sharpen with different sharpeners, my Tormek, my wicked edge and my new Tsprof k03, to keep things consistent I made these: 134812 Three...

   Liked On: 08-05-2020, 10:23 AM

4. 
   Puffin liked post by Shelley On thread : Sharpener edge test

   Waste of money, too much play means the sharpener wobbles all over the blade.

   Liked On: 06-05-2020, 03:08 PM

5. 
   viper liked post by Shelley On thread : Sharpener edge test

   Sharpener scratch patterns 2x48 belt sander 138730 Pure primary grind, fairly smooth and blends in perfectly, most expensive system, quickest to use but easy to bugger it up and takes a lot of...

   Liked On: 06-05-2020, 08:05 AM

6. 
   Tikka7mm08 liked post by Shelley On thread : Sharpener edge test

   Sharpener scratch patterns 2x48 belt sander 138730 Pure primary grind, fairly smooth and blends in perfectly, most expensive system, quickest to use but easy to bugger it up and takes a lot of...

   Liked On: 06-05-2020, 06:07 AM

7. 
   canross liked post by Shelley On thread : slingshot becomes sling bow

   Was debating about putting this into the Archery section or not but thought it might offend some our archers, and its more of a gear thing I suppose - it just also uses arrows, (mods move if need...

   Liked On: 05-05-2020, 12:47 PM

8. 
   mopheadrob liked post by Shelley On thread : Where to buy lapping film?

   bladesnz, they sell it specifically for the wicked edge but it will work on anything as the back is sticky, have various microns going down to .5, which is roughly 50000 grit...if they can’t help...

   Liked On: 30-04-2020, 08:28 PM

9. 
   Moa Hunter liked post by Shelley On thread : Sharpener edge test

   Next is the wicked edge 137970 Followed with the last one on the Tsprof k03 137970137971

   Liked On: 29-04-2020, 09:21 AM

10. 
    Moa Hunter liked post by Shelley On thread : Sharpener edge test

    Decided I want to compare the edge of some knives that I sharpen with different sharpeners, my Tormek, my wicked edge and my new Tsprof k03, to keep things consistent I made these: 134812 Three...

    Liked On: 29-04-2020, 09:19 AM

11. 
    Tikka7mm08 liked post by Shelley On thread : Sharpener edge test

    I had the spyderco sharp maker with the ultra fine rods as well, a good system with a really well thought out case, however it does not even come close to the edge I can get with the wicked edge, so...

    Liked On: 29-04-2020, 08:47 AM

12. 
    viper liked post by Shelley On thread : Sharpener edge test

    Next is the wicked edge 137970 Followed with the last one on the Tsprof k03 137970137971

    Liked On: 28-04-2020, 03:58 PM

13. 
    R93 liked post by Shelley On thread : Sharpener edge test

    Next is the wicked edge 137970 Followed with the last one on the Tsprof k03 137970137971

    Liked On: 28-04-2020, 03:40 PM

14. 
    Puffin liked post by Shelley On thread : A better knife sharpener by far...Wicked edge

    First I am not working for, sponsored by, hold stocks in or getting paid by Wicked Edge for this review, I bought my Wicked Edge with my own money. Second I own or have used a few different knife...

    Liked On: 27-04-2020, 12:48 PM

15. 
    viper liked post by Shelley On thread : Sharpener edge test

    So this one is being sharpened (now done) with this, an 84 engineering belt grinder 137777 And this one is being done on the tormek 137778 Two more to go...

    Liked On: 27-04-2020, 08:05 AM

Page 10 of 27 First 123456789101112131415161718192021222324 ... Last

• Jump to page: