shooternz
Member

983 Likes

Page 12 of 66 First 123456789101112131415161718192021222324252662 ... Last

• Jump to page:

1. 
   tetawa liked post by shooternz On thread : 12 projectile.packs

   Do have the bullet or powder manufactures reloading manual, start 2 grains under max and load up in 0.5 grain steps that is how we did it pre Chrony days, What cartridge bullet and powder?...

   Liked On: 22-05-2022, 04:39 PM

2. 
   Micky Duck liked post by shooternz On thread : 12 projectile.packs

   Do have the bullet or powder manufactures reloading manual, start 2 grains under max and load up in 0.5 grain steps that is how we did it pre Chrony days, What cartridge bullet and powder?...

   Liked On: 22-05-2022, 11:21 AM

3. 
   Cordite liked post by shooternz On thread : Wheelguns.

   I have a 586 and K38 none of the other revolvers are a patch on the Smith and Wessons straight out of the box they have great triggers and are more accurate than the shooter, Unless you want to...

   Liked On: 19-05-2022, 09:58 AM

4. 
   Micky Duck liked post by shooternz On thread : For all the 270 haters

   I doubt the Chinese actually give a toss about patching up their wounded very much; there are a surplus of them, You don't have to defeat the body armour hit a trauma plate with a standard 7.62x51...

   Liked On: 15-05-2022, 09:00 PM

5. 
   Micky Duck liked post by shooternz On thread : Rossi M951 38sp Revolver help

   Smith & Wesson K frames use a leaf spring, Any gunsmith should have a selection of springs or falling that an Engineering supplier Your Gunsmith was right only DA revolvers worth using for serious...

   Liked On: 03-05-2022, 09:11 PM

6. 
   Bill999 liked post by shooternz On thread : Sub sonic 7-08

   You need to be careful with loading Subs in the 7mm calibres you need to use bullet around 120 grains the heavier bullets are too long to stabilise at 1040fps If you don't mind a trip to Tokoroa I...

   Liked On: 03-05-2022, 09:30 AM

7. 
   Micky Duck liked post by shooternz On thread : Sub sonic 7-08

   You need to be careful with loading Subs in the 7mm calibres you need to use bullet around 120 grains the heavier bullets are too long to stabilise at 1040fps If you don't mind a trip to Tokoroa I...

   Liked On: 02-05-2022, 08:55 PM

8. 
   Cordite liked post by shooternz On thread : CAC 308 Brass

   Not in those boxes that is new brass loaded hunting ammo, The NRA Fullbore ammo came in White boxes, It is good brass if a bit variable in capacity pay to weigh it into batches and anneal it like...

   Liked On: 01-05-2022, 02:24 PM

9. 
   tetawa liked post by shooternz On thread : Fireforming oiled cases

   Stay off that site they are crazy, Oiled case were only used to test the locking lug strength at Amories and Arsenals by people that knew what they were doing and using state of the art equipment ,...

   Liked On: 27-04-2022, 06:36 PM

10. 
    Moa Hunter liked post by shooternz On thread : Fireforming oiled cases

    Stay off that site they are crazy, Oiled case were only used to test the locking lug strength at Amories and Arsenals by people that knew what they were doing and using state of the art equipment ,...

    Liked On: 27-04-2022, 09:59 AM

11. 
    T.FOYE liked post by shooternz On thread : 6.5 Carcano

    https://noebulletmolds.com/site/wp-content/uploads/2017/05/270-165-FN_GC_E1_Sketch.jpg This would be the best Bullet mold for the Cacarno the groove diameter is around .268"; .270" is no problem...

    Liked On: 15-04-2022, 09:48 AM

12. 
    Frogfeatures liked post by shooternz On thread : 6.5 Carcano

    https://noebulletmolds.com/site/wp-content/uploads/2017/05/270-165-FN_GC_E1_Sketch.jpg This would be the best Bullet mold for the Cacarno the groove diameter is around .268"; .270" is no problem...

    Liked On: 13-04-2022, 08:22 PM

13. 
    grandpamac liked post by shooternz On thread : 6.5 Carcano

    https://noebulletmolds.com/site/wp-content/uploads/2017/05/270-165-FN_GC_E1_Sketch.jpg This would be the best Bullet mold for the Cacarno the groove diameter is around .268"; .270" is no problem...

    Liked On: 13-04-2022, 07:33 PM

14. 
    mosinboy liked post by shooternz On thread : Wanting to buy 44-40 Starline brass

    I have 50 new Starline I can spare PM me

    Liked On: 13-04-2022, 01:14 PM

15. 
    Cordite liked post by shooternz On thread : 308 Twist rates v projectile weights ?

    A 1:12" twist will handle bullets from 100 grs to 200 grs as the biggest animals we shoot are Deer bullets from a .308 really don't need to be heavier than 180 grs you start losing velocity going...

    Liked On: 09-04-2022, 11:55 PM

Page 12 of 66 First 123456789101112131415161718192021222324252662 ... Last

• Jump to page: