shooternz
Member

911 Likes

Page 13 of 61 First 123456789101112131415161718192021222324252627 ... Last

• Jump to page:

1. 
   shooternz liked post by Finnwolf On thread : Oops...

   Some air rifles have a ‘silencer’ attached. Possibly the person claiming that rifle had a silencer attached is not gun-savvy enough to be qualified in making that claim.

   Liked On: 17-01-2021, 07:39 PM

2. 
   shooternz liked post by Micky Duck On thread : Speed vs pressure

   more importantly if you dont own rangefinder and arent twiddlin n fiddlin with dials....speed doesnt matter but pressure sure as hell does. Ive been known to use same load with same components and...

   Liked On: 17-01-2021, 01:54 PM

3. 
   shooternz liked post by zimmer On thread : Reloading press

   I have a JR3. Nice press but not grunty like the compound linkage models. Longest ammo I have reloaded was 7x57. No trouble full length sizing 284W. Gap between top of shellholder and the...

   Liked On: 17-01-2021, 01:52 PM

4. 
   shooternz liked post by wanneroo On thread : Reloading press

   I have an RCBS Rock Chucker and it's fine but next press will be the Redding T-7. Sierra Bullets ran a million rounds through a Redding T-7 and had it checked and zero run out or slop, as good as...

   Liked On: 17-01-2021, 01:49 PM

5. 
   shooternz liked post by ebf On thread : Standing shooting technique

   Join a service rifle club, your positional shooting should improve...

   Liked On: 03-01-2021, 09:47 PM

6. 
   shooternz liked post by Friwi On thread : New cartridge from weatherby: 6.5 RPM

   Well the 6.5-300 weatherby is going to hold that title for a while I think

   Liked On: 03-01-2021, 09:44 PM

7. 
   shooternz liked post by zimmer On thread : Help - Decapping road stuck in case

   Hornady's pathetic zip lock system. The shaft locks by friction. All other die manufacturers have threaded rods with threaded locking nuts or rings. On the Hornady there are are series of thread like...

   Liked On: 30-12-2020, 12:12 AM

8. 
   shooternz liked post by grandpamac On thread : Neck turning...is it worth doing ?

   Greetings Ftx325, Not generally thought to be a good idea on factory chambers. Makes a loose neck fit even looser. Only called for if the rifle has a tight neck chamber. These are cut that way by...

   Liked On: 22-12-2020, 08:27 AM

9. 
   shooternz liked post by dannyb On thread : Neck turning...is it worth doing ?

   Do you batch weigh your brass ? Do you anneal ? Do you uniform your flash holes ? Do you trim ? Do you batch weigh your projectiles ? Do you clean and tumble your brass ? Probably a whole heap...

   Liked On: 22-12-2020, 08:27 AM

10. 
    shooternz liked post by ebf On thread : Fireforming case with cleaning patches and pistol powder

    If you want good conformity of the brass to your chamber, you really want to use a projectile and get it jammed into the lands, so that the case base is tight against the bolt face. That way you get...

    Liked On: 19-12-2020, 12:29 AM

11. 
    shooternz liked post by Noswal On thread : Any one seating bullets using a graphite powder?

    Yes when sizing. Lube on the case, dip neck into graphite media with a twist then full size. Even after trimming, neck prep and cleaning there is still graphite in the neck to help with consistent...

    Liked On: 16-12-2020, 02:14 PM

12. 
    shooternz liked post by zimmer On thread : Auto powder dispensers

    I used an RCBS Uniflow thrower for years. Dispensed just under and finished with a trickler on my old Ohaus D5 beam scales. With the Uniflow like any thrower it is all about consistant technique/how...

    Liked On: 16-12-2020, 09:35 AM

13. 
    shooternz liked post by Ryan_Songhurst On thread : Auto powder dispensers

    A decent powder thrower is way quicker than any auto dispenser. Even my "budget" lee thrower will hold a charge from start to finish loading 50 rounds, I weigh every 5th or 6th one quickly to make...

    Liked On: 16-12-2020, 09:29 AM

14. 
    shooternz liked post by GWH On thread : Lightweight loads for 30-06

    I find the IMR4198 works far better than 2206H for reduced charge/recoil loads, it gives far better accuracy and can be used for almost any cartridge from 223 to 3006.

    Liked On: 07-12-2020, 10:22 AM

15. 
    shooternz liked post by Tahr On thread : 223 ELDM powder choice

    I use 2206 with 77 grn Tipped MK and gimp uses 2208 with 80 ELDM. I can't talk for gimp but I'm sure his is super accurate as is mine. I would load a few with each powder to try. Just go for the...

    Liked On: 07-12-2020, 10:10 AM

Page 13 of 61 First 123456789101112131415161718192021222324252627 ... Last

• Jump to page: