shooternz
Member

983 Likes

Page 21 of 66 First ... 7891011121314151617181920212223242526272829303132333435 ... Last

• Jump to page:

1. 
   mawzer308 liked post by shooternz On thread : Subsonic project

   Don't worry about fillers not needed in the .44 Mag with any of the shot gun powders, Look up loads for the .44 Special for start loads I have gone down to 6 grains of Trail Boss with the 270 HP...

   Liked On: 27-08-2021, 01:03 PM

2. 
   Micky Duck liked post by shooternz On thread : Suppressing a 45/70

   I have one of those in .44 mag and a DPT muzzle forward with 2 extra baffles even with subs it is not quiet still wear ear muffs, with it's happy load it very accurate, Really only bought it to test...

   Liked On: 26-08-2021, 09:05 PM

3. 
   Micky Duck liked post by shooternz On thread : 300 Blackout Fired In 223

   I can relate to this comment, Get people not knowing enough about cast bullets asking all sort of stupid questions that the answer is quite obvious if they thought about it. “Had some dude come...

   Liked On: 26-08-2021, 06:59 PM

4. 
   superdiver liked post by shooternz On thread : Subsonic 7mm loads

   Yes I would like a 38/55 and a 40/70 Sharps if I ever win Lotto

   Liked On: 21-08-2021, 03:32 PM

5. 
   winaa liked post by shooternz On thread : Subsonic 7mm loads

   The problem with the 7mm as a subsonic calibre is the twist rate it won't stabilise bullets longer than my 133 HP and the higher velocity is limited by the twist rate to 1700fps it really is too...

   Liked On: 20-08-2021, 05:03 PM

6. 
   Micky Duck liked post by shooternz On thread : Subsonic 7mm loads

   The problem with the 7mm as a subsonic calibre is the twist rate it won't stabilise bullets longer than my 133 HP and the higher velocity is limited by the twist rate to 1700fps it really is too...

   Liked On: 20-08-2021, 01:11 PM

7. 
   Marty Henry liked post by shooternz On thread : Subsonic 7mm loads

   The problem with the 7mm as a subsonic calibre is the twist rate it won't stabilise bullets longer than my 133 HP and the higher velocity is limited by the twist rate to 1700fps it really is too...

   Liked On: 20-08-2021, 11:33 AM

8. 
   Micky Duck liked post by shooternz On thread : 25cal hp casting oops

   Would still pay to find some way of fixing it permanently in place screws tend to shake loose when casting a lot, You need to watch the block alignment pins as well a couple of my moulds they have...

   Liked On: 18-08-2021, 08:05 PM

9. 
   Micky Duck liked post by shooternz On thread : 25cal hp casting oops

   Nope HP's are more accurate than solids all my HP moulds come with pins for both HP and solid and in every case the HP is more accurate the reason is the centre of gravity is moved more to the rear...

   Liked On: 18-08-2021, 08:01 PM

10. 
    Micky Duck liked post by shooternz On thread : 25cal hp casting oops

    My NOE moulds have a different setup for the HP I order the RG2 and RG4 style, And I never smoke them I give them a good cleaning in hot soapy water and heat them to 350 to 400 F and cool a couple...

    Liked On: 18-08-2021, 08:00 PM

11. 
    Tertle liked post by shooternz On thread : 25cal hp casting oops

    Would still pay to find some way of fixing it permanently in place screws tend to shake loose when casting a lot, You need to watch the block alignment pins as well a couple of my moulds they have...

    Liked On: 18-08-2021, 07:08 PM

12. 
    winaa liked post by shooternz On thread : 25cal hp casting oops

    Nope HP's are more accurate than solids all my HP moulds come with pins for both HP and solid and in every case the HP is more accurate the reason is the centre of gravity is moved more to the rear...

    Liked On: 18-08-2021, 06:37 PM

13. 
    Tertle liked post by shooternz On thread : 25cal hp casting oops

    Nope HP's are more accurate than solids all my HP moulds come with pins for both HP and solid and in every case the HP is more accurate the reason is the centre of gravity is moved more to the rear...

    Liked On: 18-08-2021, 02:59 PM

14. 
    Tertle liked post by shooternz On thread : 25cal hp casting oops

    My NOE moulds have a different setup for the HP I order the RG2 and RG4 style, And I never smoke them I give them a good cleaning in hot soapy water and heat them to 350 to 400 F and cool a couple...

    Liked On: 18-08-2021, 02:53 PM

15. 
    Micky Duck liked post by shooternz On thread : Projectile performance

    If hunting and shots are inside 200 metres a medium heavy round nose projectile is the best choice like the 6mm 100/105 RN 25 cal 117 RN the 6.5 156/160 RN 7mm 175 RN and the .30 180 RN as long as...

    Liked On: 14-08-2021, 10:31 AM

Page 21 of 66 First ... 7891011121314151617181920212223242526272829303132333435 ... Last

• Jump to page: