shooternz
Member

983 Likes

Page 29 of 66 First ... 1516171819202122232425262728293031323334353637383940414243 ... Last

• Jump to page:

1. 
   Micky Duck liked post by shooternz On thread : Subsonic action

   At subsonic it should never foul just clean with solvent and a few patches it is like a big .22RF, The lube is mostly wax a bit like car wax, all that is in the bore is powder residue no scrubbing...

   Liked On: 14-08-2020, 04:01 PM

2. 
   Micky Duck liked post by shooternz On thread : Subsonic action

   I am not sure of the velocity but I get good accuracy with 25.00 grains of 2206H start to get lead fouling at 35.00 grains around 2100fps in my rifles 30" barrel.

   Liked On: 14-08-2020, 04:00 PM

3. 
   mimms2 liked post by shooternz On thread : .308 vs .300blk

   If you don't hand load then it is the 300BLK subsonic loads for .308 are not readily available unless custom loaded by some one.

   Liked On: 14-08-2020, 11:40 AM

4. 
   Shearer liked post by shooternz On thread : Subsonic action

   At subsonic it should never foul just clean with solvent and a few patches it is like a big .22RF, The lube is mostly wax a bit like car wax, all that is in the bore is powder residue no scrubbing...

   Liked On: 14-08-2020, 10:56 AM

5. 
   Fat ninja liked post by shooternz On thread : .308 vs .300blk

   If you don't hand load then it is the 300BLK subsonic loads for .308 are not readily available unless custom loaded by some one.

   Liked On: 14-08-2020, 10:53 AM

6. 
   ebee liked post by shooternz On thread : The Lever Aficionados Thread

   Hi guys, I am thinking about getting a new mould for the 30/30, Just posting here to see if there is any interest from you lever action shooters in a 170 grain FP cast bullet it will be a clone of...

   Liked On: 13-08-2020, 06:12 AM

7. 
   10-Ring liked post by shooternz On thread : Concentricity Gauges

   [QUOTE=7mmsaum;1047579]Nearly EVERY Redding FL die induces runout as you pull the Sizing button up through the neck as the taper is at the wrong end of the button Take the spindle and button out...

   Liked On: 07-08-2020, 10:20 PM

8. 
   zimmer liked post by shooternz On thread : Concentricity Gauges

   [QUOTE=7mmsaum;1047579]Nearly EVERY Redding FL die induces runout as you pull the Sizing button up through the neck as the taper is at the wrong end of the button Take the spindle and button out...

   Liked On: 07-08-2020, 07:26 PM

9. 
   grandpamac liked post by shooternz On thread : .44 magnum twist rate

   A friend of mine shoots the 280gr in .44 mag Handi Rifle with a 1:38" twist with no problems other than the .432" groove diameter other guy shoots them in a .444 Marlin with the same twist it is not...

   Liked On: 04-08-2020, 05:27 PM

10. 
    ebee liked post by shooternz On thread : .44 magnum twist rate

    A friend of mine shoots the 280gr in .44 mag Handi Rifle with a 1:38" twist with no problems other than the .432" groove diameter other guy shoots them in a .444 Marlin with the same twist it is not...

    Liked On: 04-08-2020, 07:16 AM

11. 
    Micky Duck liked post by shooternz On thread : Counterfeit Leupolds

    Some people just can resist a perceived bargain like $1600 Tag watches for $50.00 in Hong Kong, If you want a cheap Leupold just go to Aliexpress cut out the middle man Check Ebay for second hand ...

    Liked On: 02-08-2020, 05:03 PM

12. 
    Cordite liked post by shooternz On thread : 308 twist rate

    The standard .308 twist is 1:12" some match/Sniper barrels are 1:11" to handle 175 SMK's any faster twist is only for the real heavies like 230 grains if you only plan on using subs occasionly it...

    Liked On: 31-07-2020, 01:30 PM

13. 
    Friwi liked post by shooternz On thread : 308 twist rate

    If you want to use cast bullets don't use a fast twist the slower the better my test rifle has a 1:13" twist and stabilises the 151HP down to 900 fps haven't tried to go lower not keen on a stuck...

    Liked On: 30-07-2020, 11:39 PM

14. 
    rupert liked post by shooternz On thread : slug and buckshot

    Go to the local scrap dealer and buy lead, wheel weights are not the best for slugs and buckshot too hard and unless you know what to look for a waste of time if you do use WW keep the temperature...

    Liked On: 30-07-2020, 06:02 PM

15. 
    mimms2 liked post by shooternz On thread : slug and buckshot

    Go to the local scrap dealer and buy lead, wheel weights are not the best for slugs and buckshot too hard and unless you know what to look for a waste of time if you do use WW keep the temperature...

    Liked On: 30-07-2020, 05:35 PM

Page 29 of 66 First ... 1516171819202122232425262728293031323334353637383940414243 ... Last

• Jump to page: