shooternz
Member

983 Likes

Page 40 of 66 First ... 2627282930313233343536373839404142434445464748495051525354 ... Last

• Jump to page:

1. 
   Micky Duck liked post by shooternz On thread : .452 bore vs .455 cast projectiles

   I saw that MD, problem is it is a single cavity it would take a long time to make a decent amount of bullets I have used one of Lymans HP moulds before gets boring very quickly, I would like it for...

   Liked On: 01-01-2019, 12:21 PM

2. 
   Micky Duck liked post by shooternz On thread : Subsonic 308 project

   You need a HP to expand lead bullets at subsonic velocity the solid versions of mine will expand at 1400fps and they are as soft as I can get them and still cast properly,

   Liked On: 29-12-2018, 12:14 PM

3. 
   10-Ring liked post by shooternz On thread : Bolt security

   Just being cheeky, My favourite traveling companion is a Ruger No1 in 6mmBR, block out while on the move couple of minutes and a screwdriver to reinstall like to see said scumbag source a new block...

   Liked On: 28-12-2018, 07:57 PM

4. 
   Micky Duck liked post by shooternz On thread : Anyone played with .30-30 subs?

   The 30/30 is one of the perfect cast bullet cartridges 170 grain cast bullets can be shot at the same velocity as jacketed.

   Liked On: 22-12-2018, 02:38 PM

5. 
   40mm liked post by shooternz On thread : What causes key holing in sub loads

   Hi Bill999, You got those 200 grain flat points off me, In theory they should be stabilised with a 1:13" twist at 1050fps, I have two .308s one shoots them the other won't it's just one of the ...

   Liked On: 21-12-2018, 05:20 PM

6. 
   Walker liked post by shooternz On thread : Light Varmint/Target Rifle ideas

   There is always the 6mm Remington I have one on a Parker Hale action with a #4 profile 25" 1:10" barrel fired 3500 rounds before being set back and re-chambered weights 9 pounds with scope favourite...

   Liked On: 14-12-2018, 07:43 PM

7. 
   Moa Hunter liked post by shooternz On thread : Light Varmint/Target Rifle ideas

   There is always the 6mm Remington I have one on a Parker Hale action with a #4 profile 25" 1:10" barrel fired 3500 rounds before being set back and re-chambered weights 9 pounds with scope favourite...

   Liked On: 14-12-2018, 11:57 AM

8. 
   csmiffy liked post by shooternz On thread : Cannot Get Headspace Short Enough?

   I tried that first didn't work that well, the cam over method is better as it takes up the flex in the press, I was surprised that a RCBS Rockchucker would have that much flex, With reloading you...

   Liked On: 05-12-2018, 07:55 PM

9. 
   Moa Hunter liked post by shooternz On thread : Woodleigh users ?

   They are used here, most hunters have no idea what bullet type they should be using the current trend is to use bullets that fragment not sure why anyone thinks that is a good idea, I like bullets...

   Liked On: 03-12-2018, 06:05 PM

10. 
    chainsaw liked post by shooternz On thread : Cannot Get Headspace Short Enough?

    I tried that first didn't work that well, the cam over method is better as it takes up the flex in the press, I was surprised that a RCBS Rockchucker would have that much flex, With reloading you...

    Liked On: 03-12-2018, 12:25 PM

11. 
    6x47 liked post by shooternz On thread : reloading press

    Redding Lyman RCBS Forster Hornady Stay away from Lee, if a press is going to break it will be a Lee before any other, I have abused my RCBS Rockchucker since 1970 never had problem with it same...

    Liked On: 02-12-2018, 08:24 PM

12. 
    Rees liked post by shooternz On thread : Woodleigh users ?

    They are used here, most hunters have no idea what bullet type they should be using the current trend is to use bullets that fragment not sure why anyone thinks that is a good idea, I like bullets...

    Liked On: 02-12-2018, 06:32 PM

13. 
    john m liked post by shooternz On thread : The Lever Aficionados Thread

    Pity there are not more .357/38 lever actions around they are perfect for plinking and bush hunting bullets range from 110grs to 200grs would like a Marlin if they start making them again they did...

    Liked On: 01-12-2018, 12:12 PM

14. 
    veitnamcam liked post by shooternz On thread : Cannot Get Headspace Short Enough?

    Try turning the die down 1/4 of a turn and cam over the the press handle, I used to think this was silly but tried it when I had the same problem and it worked a treat it takes the flex out of the...

    Liked On: 30-11-2018, 09:58 PM

15. 
    Carlsen Highway liked post by shooternz On thread : The Lever Aficionados Thread

    Standard twist for the 7.62x39 is 1:9.5" .303 1:10" no real difference re-chambering the Baikal is the only to get a new .303 with out costing a pile of cash

    Liked On: 30-11-2018, 03:22 PM

Page 40 of 66 First ... 2627282930313233343536373839404142434445464748495051525354 ... Last

• Jump to page: