shooternz
Member

983 Likes

Page 5 of 66 First 1234567891011121314151617181955 ... Last

• Jump to page:

1. 
   Jhon liked post by shooternz On thread : Red colour inside 44-40 case??

   Those CAS dudes have some strange ideas, I would not be surprised by anything they get up tu.

   Liked On: 09-12-2022, 07:57 PM

2. 
   outlander liked post by shooternz On thread : $51 for 100 LRP? Bloody hell!

   One of the cast bullet pages I am on says Fiocchi USA is building a Primer plant good news should take the pressure of the European plant now if the Europeans would stop send ammo to Ukraine we...

   Liked On: 19-11-2022, 10:51 AM

3. 
   Jhon liked post by shooternz On thread : $51 for 100 LRP? Bloody hell!

   One of the cast bullet pages I am on says Fiocchi USA is building a Primer plant good news should take the pressure of the European plant now if the Europeans would stop send ammo to Ukraine we...

   Liked On: 17-11-2022, 07:21 PM

4. 
   mikee liked post by shooternz On thread : $51 for 100 LRP? Bloody hell!

   Sheer desperation by some people it would seem, when they get to a $1.00 each I think I well make a killing.

   Liked On: 16-11-2022, 10:24 AM

5. 
   Micky Duck liked post by shooternz On thread : 300 Blackout Cast Projectiles

   I found Trail Boss not very good in my Blackout have had better success with 700X 3,5 grains works ok; any of the powders around the same burn rate would work it doesn't take much to move a cast...

   Liked On: 13-11-2022, 08:47 PM

6. 
   Eat Meater liked post by shooternz On thread : Can a 2 Inch Gun Fire a 1 Inch Bullet? - 300,000FPS - The Slow Mo Guys

   Pity it was made by two dudes that have no firearms knowledge

   Liked On: 04-11-2022, 06:10 PM

7. 
   Three O'Three liked post by shooternz On thread : Lyman M die expander

   Try cleaning the threads with alcohol first they get lube all over them, If you only have one expander button then locktite it

   Liked On: 30-10-2022, 11:08 PM

8. 
   Moa Hunter liked post by shooternz On thread : HELP! Primers

   It really depends on the powder you use any of the ADI powders don't need Magnum primers But the ball powders general benefit from the extra power, also the primer can can vary some standard primers...

   Liked On: 20-10-2022, 11:06 PM

9. 
   fluffchucker liked post by shooternz On thread : HELP! Primers

   It really depends on the powder you use any of the ADI powders don't need Magnum primers But the ball powders general benefit from the extra power, also the primer can can vary some standard primers...

   Liked On: 20-10-2022, 09:03 AM

10. 
    bumblefoot liked post by shooternz On thread : Now THIS is reloading...

    So that is where all the primers go

    Liked On: 17-10-2022, 10:32 AM

11. 
    Moa Hunter liked post by shooternz On thread : Now THIS is reloading...

    So that is where all the primers go

    Liked On: 17-10-2022, 08:13 AM

12. 
    csmiffy liked post by shooternz On thread : 8x57 projectiles

    Yes S&B 196 are fine so are the Norma of any weight, at present it is more what you can find than anything else The most common projectiles used in the 8x57 are the heavier ones in the 180 to 200...

    Liked On: 07-10-2022, 08:33 PM

13. 
    janleroux liked post by shooternz On thread : RPA2000

    The RPA is on par with the Barnard actions great for TR it is what they were designed for a friend of mine shot one for years, The actions were about $1200 to $1600 in the 1990's You can't go...

    Liked On: 01-10-2022, 09:44 AM

14. 
    Moa Hunter liked post by shooternz On thread : Cast Lead Thread ?

    The Gas Check reinforces the base when using high velocity loads also there is an improvement in accuracy when gas checking a bullet lhat is designed for them, and the bullets can be made from...

    Liked On: 29-09-2022, 04:10 PM

15. 
    Jhon liked post by shooternz On thread : Cast Lead Thread ?

    The Gas Check reinforces the base when using high velocity loads also there is an improvement in accuracy when gas checking a bullet lhat is designed for them, and the bullets can be made from...

    Liked On: 29-09-2022, 02:02 PM

Page 5 of 66 First 1234567891011121314151617181955 ... Last

• Jump to page: