shooternz
Member

911 Likes

Page 52 of 61 First ... 2383940414243444546474849505152535455565758596061 Last

• Jump to page:

1. 
   shooternz liked post by systolic On thread : Scaled IPSC targets for practice

   Or, instead of buying all those replacement parts, he could spend that money on ammo and practice shooting the gun more.

   Liked On: 09-06-2016, 06:25 PM

2. 
   shooternz liked post by ChrisF On thread : Not new but starting again....

   Single stage press powder thower balance scales a tricker and look at some hand priming unit , like lee etc

   Liked On: 06-06-2016, 08:47 PM

3. 
   shooternz liked post by Kscott On thread : Field Target Shooting

   50194 :thumbsup:

   Liked On: 02-06-2016, 03:37 PM

4. 
   shooternz liked post by nor-west On thread : Optimum weight for long range ??

   Foster, you really don't need any help or advice from any of us, I know what caliber it is :ORLY: and if it's under 24 inches it will be a waste, you will need a standard sporter #2 at least for 4 or...

   Liked On: 26-05-2016, 02:27 PM

5. 
   shooternz liked post by 25/08IMP On thread : Rifle Builds

   Don't do it unless you go long on barrel length been there now I have a .260AI 10 grains less powder and more speed with same weight bullet.

   Liked On: 17-05-2016, 01:40 PM

6. 
   shooternz liked post by Friwi On thread : Quietest firearm possible?

   A 22 bolt action rifle launching subsonic bullets in a very long barrel with a very long suppressor is the quietest you would get. The bigger the exit hole the more noise it makes. The heavier the...

   Liked On: 15-05-2016, 02:45 PM

7. 
   shooternz liked post by 10-Ring On thread : Parker Hale Restoration - Need advice

   Make sure the bottom end of the recoil pad follows the angle line of the butt right down to the toe. Have seen plenty of pads installed by D.I.Y's that had the pad squared off instead of the above...

   Liked On: 15-05-2016, 02:38 PM

8. 
   shooternz liked post by ebf On thread : Omark / Sportco Target action Q?

   best to speak to several gunsmiths and get estimates. the aus army apparently looked at converting omarks to magfeed, but the cost was prohibitive omarks do have some quirks : primary...

   Liked On: 13-05-2016, 12:54 PM

9. 
   shooternz liked post by southernman On thread : Varmint Cal

   I have a 6mm Remington, that I use, also had a .243, much prefer the 6mm Remington, bit faster, but found it far easier, to get several, projectiles to similar point of impact, 65gr v-max, and a...

   Liked On: 11-05-2016, 02:23 PM

10. 
    shooternz liked post by veitnamcam On thread : Parallax Adjustment

    No. Been there done that not needed, if you have a nice consistent cheek weld you will be fine and even if not back your eye out till the edges darken and center your eye.

    Liked On: 30-04-2016, 03:56 PM

11. 
    shooternz liked post by Tommy On thread : NZ Police import permit 'Hand in' MSSA policy

    How do gang members get guns? They apply for a firearms licence and the Police approve them…really...

    Liked On: 27-04-2016, 02:41 PM

12. 
    shooternz liked post by stug On thread : First deer with the 9.3x62

    Warning - this is long and no pics. I had started writing this with the intention of sending it to a magazine for publishing, but i forgot my camera so have no photos of the stag i shot. ...

    Liked On: 21-04-2016, 11:31 AM

13. 
    shooternz liked post by Tentman On thread : Advice on new scope

    First decide if you want a 30mm tube or not, they are the fashionable choice at the moment but as with most things firearms its mostly hype. The only benefit of a 30 is that you'll have more travel...

    Liked On: 17-04-2016, 06:03 PM

14. 
    shooternz liked post by 7x64 On thread : Best brass?

    I despise hornady brass. It seems to vary hugely from OK to complete and utter garbage depending on the batch. Go and buy some Lapua or Norma and save yourself a huge amount of headaches. I would...

    Liked On: 15-04-2016, 03:39 PM

15. 
    shooternz liked post by Timmay On thread : T3 Half- cock issue

    Unpopular opinion here. Why do you need half cock if your rifle is always pointed in a safe direction? Load a round and put on the safety - keep your finger off the trigger.

    Liked On: 12-04-2016, 01:49 PM

Page 52 of 61 First ... 2383940414243444546474849505152535455565758596061 Last

• Jump to page: