shooternz
Member

983 Likes

Page 65 of 66 First ... 1551525354555657585960616263646566 Last

• Jump to page:

1. 
   Gibo liked post by shooternz On thread : Windage over to one side?

   The Remingtons have that problem the screw holes are on the piss I have 5 700's none are any use with rails I have tried a few rails not cheap Chinese junk, expensive US made stuff none were of much...

   Liked On: 07-05-2015, 10:55 PM

2. 
   deepsouthaussie liked post by shooternz On thread : Subsonic 22lr going supersonic?

   The most reliable .22 Subs are the Aussie made Winchester, Also the most pricey

   Liked On: 20-04-2015, 04:02 PM

3. 
   heinnz liked post by shooternz On thread : 75gr Amax 223, UPDATE

   You're going about it all wrong, the easiest way to test your loads is to shoot 3 shot groups at separate aiming marks I use adhesive 20mm stickers on a piece of cardboard big enough to take the all...

   Liked On: 18-04-2015, 03:54 PM

4. 
   rambo-6mmrem liked post by shooternz On thread : Subsonic 22lr going supersonic?

   The most reliable .22 Subs are the Aussie made Winchester, Also the most pricey

   Liked On: 12-04-2015, 02:39 PM

5. 
   JRW87 liked post by shooternz On thread : Subsonic 22lr going supersonic?

   The most reliable .22 Subs are the Aussie made Winchester, Also the most pricey

   Liked On: 12-04-2015, 09:26 AM

6. 
   Hunt4life liked post by shooternz On thread : 75gr Amax 223, UPDATE

   You're going about it all wrong, the easiest way to test your loads is to shoot 3 shot groups at separate aiming marks I use adhesive 20mm stickers on a piece of cardboard big enough to take the all...

   Liked On: 08-04-2015, 03:07 PM

7. 
   kiwi39 liked post by shooternz On thread : 75gr Amax 223, UPDATE

   You're going about it all wrong, the easiest way to test your loads is to shoot 3 shot groups at separate aiming marks I use adhesive 20mm stickers on a piece of cardboard big enough to take the all...

   Liked On: 07-04-2015, 09:06 PM

8. 
   JRW87 liked post by shooternz On thread : who else casts there own bullets

   If the tyre shops want $5.00 kg for wheel weights they are dreaming the going rate is $2.00 kg to buy from the scrap dealers, I pay the tyre shops a $1.00 kg and have all 4 shops in town saving them...

   Liked On: 07-03-2015, 06:13 PM

9. 
   Maca49 liked post by shooternz On thread : who else casts there own bullets

   Your Lino is short on tin I would say, get some 50/50 solder from the plumbers suppliers 1 stick to 10kg works with my mix which is wheel weights for pistol bullets and a mix of wheel weights and...

   Liked On: 06-03-2015, 06:02 AM

10. 
    stumpy liked post by shooternz On thread : who else casts there own bullets

    Your Lino is short on tin I would say, get some 50/50 solder from the plumbers suppliers 1 stick to 10kg works with my mix which is wheel weights for pistol bullets and a mix of wheel weights and...

    Liked On: 05-03-2015, 03:41 PM

11. 
    res liked post by shooternz On thread : who else casts there own bullets

    Your Lino is short on tin I would say, get some 50/50 solder from the plumbers suppliers 1 stick to 10kg works with my mix which is wheel weights for pistol bullets and a mix of wheel weights and...

    Liked On: 05-03-2015, 03:39 PM

12. 
    Mauser308 liked post by shooternz On thread : CCI primer misfires?

    One thing you could try is polishing the inside of the bolt if the spring is binding a little it could slow the firing pin strike down, I have seen it in a couple of Rem 700's and heard of it in...

    Liked On: 04-03-2015, 10:53 PM

13. 
    Yukon liked post by shooternz On thread : FMJ on animals

    Go find an old gunsmith and ask him, When I first started shooting I used to hang out at the local gunshop quite a lot the gunsmith that owned it was ex army and had a stack of .303 barrels taken...

    Liked On: 13-02-2015, 12:45 AM

14. 
    Toby liked post by shooternz On thread : FMJ on animals

    Go find an old gunsmith and ask him, When I first started shooting I used to hang out at the local gunshop quite a lot the gunsmith that owned it was ex army and had a stack of .303 barrels taken...

    Liked On: 11-02-2015, 04:51 PM

15. 
    Marty Henry liked post by shooternz On thread : FMJ on animals

    Go find an old gunsmith and ask him, When I first started shooting I used to hang out at the local gunshop quite a lot the gunsmith that owned it was ex army and had a stack of .303 barrels taken...

    Liked On: 11-02-2015, 03:36 PM

Page 65 of 66 First ... 1551525354555657585960616263646566 Last

• Jump to page: