Simon
Member

293 Likes

Page 18 of 20 First ... 4567891011121314151617181920 Last

• Jump to page:

1. 
   R93 liked post by Simon On thread : New to IPSC

   Some hints and tips. - As a RH shooter moving and shooting moving to your right will always be easier and faster than moving to your left. Your body will be on the correct side to shoot. - When...

   Liked On: 28-08-2015, 08:58 PM

2. 
   Sasquatch liked post by Simon On thread : Vortex Strike Eagle 1-6

   Fired another 100 plus rounds using mine today. Like it a lot. Switch view leaver makes changing the magnification on the fly easy and quick. First time using this and was easy to pickup and use...

   Liked On: 26-07-2015, 01:22 AM

3. 
   Steve123 liked post by Simon On thread : Do you think you've got enough guns ?

   His guns to ammo ratio is not quite right. 1200 guns should work out to about 7-10 tons of ammo. That's what I work on anyway.

   Liked On: 24-07-2015, 07:17 PM

4. 
   steven liked post by Simon On thread : Once fired, processing

   I put 2 or 3 hundred cases on a towel at a time in a rough single layer lying as they fall then give them one or two spritzers max with Dillon Case Lube then give them a good roll around on the...

   Liked On: 16-06-2015, 02:21 PM

5. 
   shooternz liked post by Simon On thread : Once fired, processing

   I put 2 or 3 hundred cases on a towel at a time in a rough single layer lying as they fall then give them one or two spritzers max with Dillon Case Lube then give them a good roll around on the...

   Liked On: 15-06-2015, 11:20 PM

6. 
   Beaker liked post by Simon On thread : Once fired, processing

   I put 2 or 3 hundred cases on a towel at a time in a rough single layer lying as they fall then give them one or two spritzers max with Dillon Case Lube then give them a good roll around on the...

   Liked On: 15-06-2015, 10:29 PM

7. 
   Beaker liked post by Simon On thread : Cheap powder ADI

   Email Bill Wright for powder, projectiles, primers. sales@rusa.co.nz His prices and service is tops. Buying a reasonable amount always helps keep the price down.

   Liked On: 03-06-2015, 08:12 AM

8. 
   Carpe Diem liked post by Simon On thread : Odd 300 blackout loading

   What's the head stamp on the case that has flared out when the projectile was seated? Is it the same as the others? I am picking that the wall thickness of that case is too thick. There are quite a...

   Liked On: 14-05-2015, 12:50 AM

9. 
   Beaker liked post by Simon On thread : Aoraki Amunition Company

   If this ammo hangs around (Is readily available) then even I will buy some just to get the case to reload. Will it continue to be available? Its close cost wise for my first round reload cost where...

   Liked On: 26-04-2015, 10:31 PM

10. 
    steven liked post by Simon On thread : Aoraki Amunition Company

    If this ammo hangs around (Is readily available) then even I will buy some just to get the case to reload. Will it continue to be available? Its close cost wise for my first round reload cost where...

    Liked On: 26-04-2015, 10:25 PM

11. 
    R93 liked post by Simon On thread : Aoraki Amunition Company

    If this ammo hangs around (Is readily available) then even I will buy some just to get the case to reload. Will it continue to be available? Its close cost wise for my first round reload cost where...

    Liked On: 26-04-2015, 10:09 PM

12. 
    Beaker liked post by Simon On thread : Looking for a progressive press

    Hi Beaker. I have from memory, 10 small rifle pickup tubes and 5 large rifle pick up tubes. I picked up extra tubes with the 550B press I got off Trade me. I load them by hand using a Dillon flip...

    Liked On: 01-04-2015, 08:32 PM

13. 
    Tommy liked post by Simon On thread : Looking for a progressive press

    Hi Beaker. I have from memory, 10 small rifle pickup tubes and 5 large rifle pick up tubes. I picked up extra tubes with the 550B press I got off Trade me. I load them by hand using a Dillon flip...

    Liked On: 01-04-2015, 07:34 PM

14. 
    mikee liked post by Simon On thread : Looking for a progressive press

    Get yourself a Dillon 550B. Strength, easy of function and the no BS warranty makes it a winner. I have two 550B and a 650. I am much like Spanners, my 650 is set up for 38 super comp and does...

    Liked On: 01-04-2015, 04:23 PM

15. 
    DAF liked post by Simon On thread : Case new OAL magazine issue

    Take it to an engineering shop and get them to mill it out. A 6mm cutter plunged in would do it easy. Will be far more tidy than grinding it out.

    Liked On: 05-02-2015, 09:38 AM

Page 18 of 20 First ... 4567891011121314151617181920 Last

• Jump to page: