Simon
Member

293 Likes

Page 9 of 20 First 1234567891011121314151617181920 Last

• Jump to page:

1. 
   Tikka7mm08 liked post by Simon On thread : AMP Annealing Service for Forum Members?

   Thanks for doing my 119 6.5 Creedmoor cases. I loaded them all back up tonight ready for next weekend along with another 100 cases I just bought.

   Liked On: 10-06-2017, 11:34 PM

2. 
   Ryan_Songhurst liked post by Simon On thread : Do you think you've got enough guns ?

   His guns to ammo ratio is not quite right. 1200 guns should work out to about 7-10 tons of ammo. That's what I work on anyway.

   Liked On: 09-06-2017, 07:02 PM

3. 
   300AAC liked post by Simon On thread : Anyone Used Black Watch Reloading Ltd Before?

   I ordered 3 packets of 6.5 projectiles. Freight was $5. They are Auckland based.

   Liked On: 20-02-2017, 08:25 PM

4. 
   300AAC liked post by Simon On thread : Anyone Used Black Watch Reloading Ltd Before?

   Ordered some Hornady projectiles from them last night and they have sharp prices. Projectiles are already on their way with tracking details sent so all good so far. Home - Transparent Header -...

   Liked On: 20-02-2017, 08:25 PM

5. 
   shooternz liked post by Simon On thread : Piece of shit fucking Redding Big Boss press!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

   Dillon.

   Liked On: 04-02-2017, 01:01 PM

6. 
   carlhurley liked post by Simon On thread : New Dillon Press

   I have a My Bullet Feeder and 10 primer pick up tubes for my 650. Can easily do 1200 rounds per hour. Picking up 1000 primers is the part I hate. I flip 500 at a time to cut time.

   Liked On: 31-01-2017, 09:56 PM

7. 
   seano liked post by Simon On thread : New Dillon Press

   I have a My Bullet Feeder and 10 primer pick up tubes for my 650. Can easily do 1200 rounds per hour. Picking up 1000 primers is the part I hate. I flip 500 at a time to cut time.

   Liked On: 31-01-2017, 09:43 PM

8. 
   Beaker liked post by Simon On thread : New Dillon Press

   I have a My Bullet Feeder and 10 primer pick up tubes for my 650. Can easily do 1200 rounds per hour. Picking up 1000 primers is the part I hate. I flip 500 at a time to cut time.

   Liked On: 31-01-2017, 08:23 PM

9. 
   mikee liked post by Simon On thread : Importing a .338 or 50cal

   Both 338 and 50 cal rifles are freely available already in NZ and can be purchased off the shelf by anyone with an A cat licence. What you have been asked to do is BS.

   Liked On: 20-01-2017, 10:27 PM

10. 
    veitnamcam liked post by Simon On thread : Importing a .338 or 50cal

    Both 338 and 50 cal rifles are freely available already in NZ and can be purchased off the shelf by anyone with an A cat licence. What you have been asked to do is BS.

    Liked On: 20-01-2017, 09:10 PM

11. 
    Tangobravo liked post by Simon On thread : RED DOT SIGHT FOR A VZ58

    Holosun

    Liked On: 20-01-2017, 08:05 PM

12. 
    Simo liked post by Simon On thread : Reloading .223/5.56 for an AR15

    Buy a case guage. These are a must. I use this type for both 223 and 300 blackout. Sheridan Engineering - Slotted Ammunition Gauges (http://www.sheridanengineering.com/index-2.htm)

    Liked On: 06-01-2017, 02:43 PM

13. 
    199p liked post by Simon On thread : AR 9mm Set Up?

    I advise you not to get one. They are crazy fun to shoot and you will burn through a shed load of ammo. Had a couple of issues with my Stag 9T but all in all, its one of my go to guns.

    Liked On: 03-01-2017, 03:45 PM

14. 
    Beaker liked post by Simon On thread : AR 9mm Set Up?

    I advise you not to get one. They are crazy fun to shoot and you will burn through a shed load of ammo. Had a couple of issues with my Stag 9T but all in all, its one of my go to guns.

    Liked On: 03-01-2017, 02:27 PM

15. 
    P38 liked post by Simon On thread : Show us your reloading bench

    Dillon 550 and Dillon 650 with case feeder and bullet feeder. I load 223, 300 blackout, 308, 9mm, 38 super. 60831

    Liked On: 18-12-2016, 08:23 AM

Page 9 of 20 First 1234567891011121314151617181920 Last

• Jump to page: