sixtus
Member

103 Likes

Page 5 of 7 First 1234567 Last

• Jump to page:

1. 
   sixtus liked post by Cigar On thread : Rangefinder and scope setups for subsonics

   I have only just finished getting my subsonic rig sorted. Bergara 16.5" 308 with DPT mini centrefire suppressor, VX1 2-7x33 scope. Load is 8.0 grains of Trailboss behind Robert's 151gr cast hollow...

   Liked On: 19-11-2019, 11:45 PM

2. 
   sixtus liked post by Bill999 On thread : Rangefinder and scope setups for subsonics

   I use the distance between my trees (7m) and break my subs trajectory up into 7m sections printed and stuck to my stock with clear tape then just count trees Iv noticed you have to be quite...

   Liked On: 19-11-2019, 11:44 PM

3. 
   sixtus liked post by tanqueray On thread : Classy lightweight takedown

   I like this idea. Wonder if you could replace the screw with a push pin...

   Liked On: 19-11-2019, 02:54 AM

4. 
   sixtus liked post by imaca On thread : chronic wasting disease

   Unfortunately they don't suffer from it - we do.

   Liked On: 17-11-2019, 05:53 PM

5. 
   sixtus liked post by Shearer On thread : Noise level of subsonic calibres

   So you can shoot cowboys over in Aussie but you can't have suppressors? Strange country.:D

   Liked On: 14-11-2019, 04:39 AM

6. 
   sixtus liked post by hotbarrels On thread : Best zero for a .357 rifle.

   You are correct! Too used to converting imperial to metric, I took the ballistics table values in cm and multiplied them by 25.4 thinking they were inches :roll: That said, I still sight in at...

   Liked On: 12-11-2019, 05:25 AM

7. 
   sixtus liked post by 223nut On thread : Photos your proud of -not just hunting

   Evil bloody birds, got chased by one orienteering , sure made me run faster

   Liked On: 04-11-2019, 11:18 PM

8. 
   sixtus liked post by Cordite On thread : Ordered a 45ACP/12ga rifled insert

   Those inserts you can buy often centre by means of O-rings. Turning down a barrel to be epoxied inside a brass 12G cartridge would seem to be the way to protect the SG chamber - and cut away a...

   Liked On: 04-11-2019, 03:50 PM

9. 
   sixtus liked post by canross On thread : Ordered a 45ACP/12ga rifled insert

   Brass shotgun cartridge, now that's using your head and keeping it simple! Don't know if I've seen many inserts in anything more than pistol calibers? I was thinking of a rifle length firearm in...

   Liked On: 04-11-2019, 03:50 PM

10. 
    sixtus liked post by Cordite On thread : Ordered a 45ACP/12ga rifled insert

    I can see someone coming up with a choke insert with a disc at the muzzle end drilled for the appropriate diameter, plus a bit extra for tolerance. Crap suppressor no doubt, but a flash hider, yes....

    Liked On: 04-11-2019, 03:50 PM

11. 
    sixtus liked post by Brakelie On thread : Ordered a 45ACP/12ga rifled insert

    What about a barrel insert with a built in suppressor on the end of it? Sent from my SM-N960F using Tapatalk

    Liked On: 04-11-2019, 03:50 PM

12. 
    sixtus liked post by Bill999 On thread : Ordered a 45ACP/12ga rifled insert

    putting it muzzle forward would be asking even harder for baffle strike unless you cut it down and done a muzzle forward on like a 4 inch barrel a series of washers that are 12 ga on the outside...

    Liked On: 04-11-2019, 03:50 PM

13. 
    sixtus liked post by Cordite On thread : Ordered a 45ACP/12ga rifled insert

    If you look at the "solvent trap" image. Imagine the inner part of the solvent trap turned down to 18-19mm diameter (whatever the precise 12g dimension is) and screwed onto the barrel insert. ...

    Liked On: 04-11-2019, 03:49 PM

14. 
    sixtus liked post by Bill999 On thread : Ordered a 45ACP/12ga rifled insert

    Be a cool idea to use the rest of the 12ga hole as a suppressor if you could ensure insert and baffle alignment

    Liked On: 04-11-2019, 03:30 PM

15. 
    sixtus liked post by skyflyhigh On thread : Ordered a 45ACP/12ga rifled insert

    Sounds like they be a bit of fun , where did you order them from and what calibers they come in ? Sent from my SM-G960F using Tapatalk

    Liked On: 29-10-2019, 10:57 PM

Page 5 of 7 First 1234567 Last

• Jump to page: