SixtyTen
Member

388 Likes

Page 14 of 26 First 1234567891011121314151617181920212223242526 Last

• Jump to page:

1. 
   SixtyTen liked post by rossi.45 On thread : Cast bullet Varminting / Medium game Project

   pages were taken from this book . . 687 pages has a big section on the American Civil War with lots of mentions of the Whitworth and the men and their exploits 186641

   Liked On: 28-12-2021, 10:31 PM

2. 
   SixtyTen liked post by rossi.45 On thread : Cast bullet Varminting / Medium game Project

   186640

   Liked On: 28-12-2021, 10:31 PM

3. 
   SixtyTen liked post by rossi.45 On thread : Cast bullet Varminting / Medium game Project

   186639

   Liked On: 28-12-2021, 10:31 PM

4. 
   SixtyTen liked post by rossi.45 On thread : Cast bullet Varminting / Medium game Project

   Hollow points should taper generally at sub velocity the bullet expands to the base of the HP if it is flat bottomed the nose will get wiped off rather than expand . . . at first glance you...

   Liked On: 23-12-2021, 10:06 PM

5. 
   SixtyTen liked post by shooternz On thread : Cast bullet Varminting / Medium game Project

   My 151HP recovered from a goat velocity 1040fps ATTACH]186468[/ATTACH] All the recovered bullets look like this most heart/lung shots exit

   Liked On: 23-12-2021, 10:06 PM

6. 
   SixtyTen liked post by rossi.45 On thread : Cast bullet Varminting / Medium game Project

   ran out of time to do more casting but enough to be able to pick out a few good bullets later to shoot some groups. 160grn. Lyman left . . 150grn. Lyman right 186266 bit of a rough plan...

   Liked On: 20-12-2021, 05:04 PM

7. 
   SixtyTen liked post by rossi.45 On thread : Cast bullet Varminting / Medium game Project

   short n fast update . . i have Lead heating up interesting day on the farm . . some good, some not so good, some challenges. same weather as last range session, drizzle n windy, similar...

   Liked On: 20-12-2021, 05:04 PM

8. 
   SixtyTen liked post by grandpamac On thread : Casting for an SMLE

   Greetings @Sixty Ten, You might want a collector to look at the hollow point cartridge. The Brits did make a hollow point 215 grain in the Calcuta Arsenal or it might just be a Mark VI that someone...

   Liked On: 18-12-2021, 09:36 AM

9. 
   SixtyTen liked post by rossi.45 On thread : Cast bullet Varminting / Medium game Project

   a small amount of lube on the base of the bullet . . you'd think it would leave a coating on the bore that the next bullet would run into and cause problems . . but it doesn'nt, i've never had...

   Liked On: 16-12-2021, 06:43 PM

10. 
    SixtyTen liked post by rossi.45 On thread : Cast bullet Varminting / Medium game Project

    i have a cunning plan . . . looking at the 170grn. Lyman round nose and measuring the bore riding nose and pushing the nose into the bore, i see its just on .301 and leaves slight engraving, maybe...

    Liked On: 16-12-2021, 06:42 PM

11. 
    SixtyTen liked post by shooternz On thread : Casting for an SMLE

    Get in touch I have some .314" 210 grain cast if you want to try some

    Liked On: 16-12-2021, 06:11 PM

12. 
    SixtyTen liked post by Driverman On thread : Casting for an SMLE

    Im watching this thread with interest. Powdercoating is just a term for providing a polymer coating to a projectile The coating is a good deal harder than the lead and if done right will not leave a...

    Liked On: 14-12-2021, 04:23 PM

13. 
    SixtyTen liked post by Micky Duck On thread : Casting for an SMLE

    grab some cast ones off shootersnz / Robert and TRY them at standard size and just see..you may be making things harder than need be.

    Liked On: 14-12-2021, 04:22 PM

14. 
    SixtyTen liked post by Joe_90 On thread : Solving a Sako design fault

    Very nice work! When I saw the thread title I was half expecting to see a photo of a howa :D

    Liked On: 13-12-2021, 05:38 PM

15. 
    SixtyTen liked post by gundoc On thread : Solving a Sako design fault

    The Sako .22 P94S has a design fault in the bolt locking ring which can cause the bolt handle and locking lug to break off the bolt during opening. This problem is caused by a combination of a steep...

    Liked On: 13-12-2021, 05:34 PM

Page 14 of 26 First 1234567891011121314151617181920212223242526 Last

• Jump to page: