SixtyTen
Member

556 Likes

Page 16 of 38 First ... 23456789101112131415161718192021222324252627282930 ... Last

• Jump to page:

1. 
   PaulNZ liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

   I'm planning to go through all the 22 ammo I have on hand and check the lead hardness. I'll post results here once I have them.

   Liked On: 15-11-2022, 07:38 PM

2. 
   techno retard liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

   I'm planning to go through all the 22 ammo I have on hand and check the lead hardness. I'll post results here once I have them.

   Liked On: 15-11-2022, 06:26 PM

3. 
   Moa Hunter liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

   Yes I can't see why not for Lead bullets. Lead hardness would be the limiting factor I think. You would also need the projectile to be supported in the correct diameter die during the punching...

   Liked On: 15-11-2022, 11:17 AM

4. 
   Joe_90 liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

   I'm planning to go through all the 22 ammo I have on hand and check the lead hardness. I'll post results here once I have them.

   Liked On: 15-11-2022, 11:15 AM

5. 
   quentin liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

   I'm planning to go through all the 22 ammo I have on hand and check the lead hardness. I'll post results here once I have them.

   Liked On: 15-11-2022, 09:41 AM

6. 
   Morepork liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

   Hey Folks, I have been working on a 22lr resizing / hollow pointing tool. What I have made is basically a direct copy of the Neal Waltz die, with a couple of minor changes. His design is by far the...

   Liked On: 14-11-2022, 11:52 PM

7. 
   techno retard liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

   Ok, sounds like a lot of interest in these dies. I'm not opposed to doing a run of these. However they are quite a bit of work, so likely to not be cheap, but likely less than it would cost to import...

   Liked On: 14-11-2022, 06:52 PM

8. 
   techno retard liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

   Hey Folks, I have been working on a 22lr resizing / hollow pointing tool. What I have made is basically a direct copy of the Neal Waltz die, with a couple of minor changes. His design is by far the...

   Liked On: 14-11-2022, 06:42 PM

9. 
   techno retard liked post by SixtyTen On thread : Hollow Point 22lr to reduce Ricochets

   I have made a hollow point tool and shot a few into wet pack newspaper. Seems to expand nicely and stopped after about 150mm. 210198 I have been looking around for a reasonably priced PCP and...

   Liked On: 14-11-2022, 06:21 PM

10. 
    veitnamcam liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

    Yes, I shoot at the Howick range in Auckland on a Wednesday night. It's only 25m, but the ammo I'm trying to improve is for 25m. At 25m top quality match ammo shoots a slightly oval hole from my...

    Liked On: 14-11-2022, 05:31 PM

11. 
    csmiffy liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

    Ok, sounds like a lot of interest in these dies. I'm not opposed to doing a run of these. However they are quite a bit of work, so likely to not be cheap, but likely less than it would cost to import...

    Liked On: 14-11-2022, 05:12 PM

12. 
    csmiffy liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

    I have noticed that certain brands are definitely much harder lead. For example, CCI std is extremely hard and does not take a hollow point that well. SK match is the softest I have found so far.

    Liked On: 14-11-2022, 05:09 PM

13. 
    Micky Duck liked post by SixtyTen On thread : Hollow Point 22lr to reduce Ricochets

    I have made a hollow point tool and shot a few into wet pack newspaper. Seems to expand nicely and stopped after about 150mm. 210198 I have been looking around for a reasonably priced PCP and...

    Liked On: 14-11-2022, 04:59 PM

14. 
    Moa Hunter liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

    Yes, I shoot at the Howick range in Auckland on a Wednesday night. It's only 25m, but the ammo I'm trying to improve is for 25m. At 25m top quality match ammo shoots a slightly oval hole from my...

    Liked On: 14-11-2022, 02:40 PM

15. 
    Moa Hunter liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

    I have noticed that certain brands are definitely much harder lead. For example, CCI std is extremely hard and does not take a hollow point that well. SK match is the softest I have found so far.

    Liked On: 14-11-2022, 02:39 PM

Page 16 of 38 First ... 23456789101112131415161718192021222324252627282930 ... Last

• Jump to page: