SixtyTen
Member

554 Likes

Page 8 of 37 First 12345678910111213141516171819202122 ... Last

• Jump to page:

1. 
   kristopher liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

   It's often interesting how much a few small changes can improve a rifle. And you also get the rifles that no matter what you do, won't improve.

   Liked On: 25-05-2024, 02:15 PM

2. 
   40mm liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

   Ok, sounds like a lot of interest in these dies. I'm not opposed to doing a run of these. However they are quite a bit of work, so likely to not be cheap, but likely less than it would cost to import...

   Liked On: 25-05-2024, 01:10 PM

3. 
   40mm liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

   Hey Folks, I have been working on a 22lr resizing / hollow pointing tool. What I have made is basically a direct copy of the Neal Waltz die, with a couple of minor changes. His design is by far the...

   Liked On: 25-05-2024, 01:08 PM

4. 
   Micky Duck liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

   Marco, I have sent you an email.

   Liked On: 25-05-2024, 12:56 PM

5. 
   MarcoT liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

   Hi Marco, around $65NZD to ship to Canada. Make a few more posts around the forum and I will be able to Private message you.

   Liked On: 25-05-2024, 09:33 AM

6. 
   MarcoT liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

   Dont worry fellas, im not going to disappear with your deposits. These are just turning out to be much more work than I expected and I only have about 3 hours a week I can work on them. I have the...

   Liked On: 25-05-2024, 08:47 AM

7. 
   Fssprecision liked post by SixtyTen On thread : 22lr Resizing/Hollow Pointing Tool

   Dont worry fellas, im not going to disappear with your deposits. These are just turning out to be much more work than I expected and I only have about 3 hours a week I can work on them. I have the...

   Liked On: 25-05-2024, 05:06 AM

8. 
   makka liked post by SixtyTen On thread : Looking for a Good Shooting Optometrist

   Hey Folks, I have astigmatism in both eyes, plus short sight in left and long sight in right. I recently visited a local optometrist and was not impressed with them at all. Can anyone recommend a...

   Liked On: 12-05-2024, 10:06 AM

9. 
   dannyb liked post by SixtyTen On thread : The lightening project

   Looks great, I have modelled similar cuts for a few different actions. Trouble is my mill is manual. How much weight does it save? My tikka T3 action was 476g before I took to it with a mill. I only...

   Liked On: 05-05-2024, 05:26 PM

10. 
    Gkp liked post by SixtyTen On thread : The lightening project

    Looks great, I have modelled similar cuts for a few different actions. Trouble is my mill is manual. How much weight does it save? My tikka T3 action was 476g before I took to it with a mill. I only...

    Liked On: 05-05-2024, 02:41 PM

11. 
    JBNZ liked post by SixtyTen On thread : Tikka T3 Stock Paint job

    Great info, thanks for that. I spent ages looking for something to add some texture to mine, from nonskid grit for boats to truck bed liner. Never though about using this underneath a colored top...

    Liked On: 20-04-2024, 03:12 PM

12. 
    rupert liked post by SixtyTen On thread : Fixing Belted Magnum Bulge - DIY Method

    Hello Gents, I recently purchased a 7mm Rem Mag Browning X-Bolt and also bought some once fired Norma brass off Trademe. I found that the cases all had a bad bulge right in front of the belt....

    Liked On: 13-04-2024, 09:30 PM

13. 
    Micky Duck liked post by SixtyTen On thread : Fixing Belted Magnum Bulge - DIY Method

    Hello Gents, I recently purchased a 7mm Rem Mag Browning X-Bolt and also bought some once fired Norma brass off Trademe. I found that the cases all had a bad bulge right in front of the belt....

    Liked On: 13-04-2024, 06:07 PM

14. 
    Makros liked post by SixtyTen On thread : Chamber Casting With Sulphur And Graphite

    Hey Folks, I thought this could be useful and might interest a few here. I read about this technique on another forum and decided to give it a go. I wanted to make a chamber cast of my No1mk3...

    Liked On: 10-03-2024, 03:21 PM

15. 
    Pixie Z liked post by SixtyTen On thread : Baikal single shot rebarrel - Anyone done this?

    I have finally finished this "quick side project" more or less. I just need make a thread protector and to get a load that shoots ok. Bit hard at the moment being stuck in the middle of the suburbs....

    Liked On: 21-02-2024, 09:06 PM

Page 8 of 37 First 12345678910111213141516171819202122 ... Last

• Jump to page: