Skirch
Member

113 Likes

Page 7 of 8 First 12345678 Last

• Jump to page:

1. 
   Morepork liked post by Skirch On thread : First stock bedding Job

   Bought a remington 700 tactical as I've always wanted one with a mcmillan style stock for long range. Found a stock on trademe for $470 which seemed like a good deal, but when it arrived it wasn't...

   Liked On: 11-02-2021, 06:55 AM

2. 
   canuck hunter liked post by Skirch On thread : First stock bedding Job

   Bought a remington 700 tactical as I've always wanted one with a mcmillan style stock for long range. Found a stock on trademe for $470 which seemed like a good deal, but when it arrived it wasn't...

   Liked On: 31-01-2021, 05:33 AM

3. 
   bunji liked post by Skirch On thread : First stock bedding Job

   After mixing up the compound that was too runny, I split off half of it to thicken it up without risking ruining the whole lot. In hindsight I should have thickened the whole lot. Mistake three was...

   Liked On: 30-01-2021, 10:52 PM

4. 
   bunji liked post by Skirch On thread : First stock bedding Job

   Bought a remington 700 tactical as I've always wanted one with a mcmillan style stock for long range. Found a stock on trademe for $470 which seemed like a good deal, but when it arrived it wasn't...

   Liked On: 30-01-2021, 10:34 PM

5. 
   RUMPY liked post by Skirch On thread : First stock bedding Job

   Bought a remington 700 tactical as I've always wanted one with a mcmillan style stock for long range. Found a stock on trademe for $470 which seemed like a good deal, but when it arrived it wasn't...

   Liked On: 30-01-2021, 06:42 PM

6. 
   Frogfeatures liked post by Skirch On thread : First stock bedding Job

   A snap of the machining toolpaths. 159192 A snap of the sketch I used to get the heights correct. 159193 Next I cleaned out the height references I left in for gluing the pillars in place and...

   Liked On: 30-01-2021, 05:19 PM

7. 
   SixtyTen liked post by Skirch On thread : First stock bedding Job

   After mixing up the compound that was too runny, I split off half of it to thicken it up without risking ruining the whole lot. In hindsight I should have thickened the whole lot. Mistake three was...

   Liked On: 30-01-2021, 05:03 PM

8. 
   Moa Hunter liked post by Skirch On thread : First stock bedding Job

   After mixing up the compound that was too runny, I split off half of it to thicken it up without risking ruining the whole lot. In hindsight I should have thickened the whole lot. Mistake three was...

   Liked On: 30-01-2021, 01:24 PM

9. 
   quentin liked post by Skirch On thread : First stock bedding Job

   After mixing up the compound that was too runny, I split off half of it to thicken it up without risking ruining the whole lot. In hindsight I should have thickened the whole lot. Mistake three was...

   Liked On: 30-01-2021, 01:22 PM

10. 
    Moa Hunter liked post by Skirch On thread : First stock bedding Job

    A snap of the machining toolpaths. 159192 A snap of the sketch I used to get the heights correct. 159193 Next I cleaned out the height references I left in for gluing the pillars in place and...

    Liked On: 30-01-2021, 01:07 PM

11. 
    Moa Hunter liked post by Skirch On thread : First stock bedding Job

    Bought a remington 700 tactical as I've always wanted one with a mcmillan style stock for long range. Found a stock on trademe for $470 which seemed like a good deal, but when it arrived it wasn't...

    Liked On: 30-01-2021, 01:05 PM

12. 
    Steve123 liked post by Skirch On thread : First stock bedding Job

    After mixing up the compound that was too runny, I split off half of it to thicken it up without risking ruining the whole lot. In hindsight I should have thickened the whole lot. Mistake three was...

    Liked On: 30-01-2021, 12:02 PM

13. 
    Micky Duck liked post by Skirch On thread : First stock bedding Job

    After mixing up the compound that was too runny, I split off half of it to thicken it up without risking ruining the whole lot. In hindsight I should have thickened the whole lot. Mistake three was...

    Liked On: 30-01-2021, 11:55 AM

14. 
    Micky Duck liked post by Skirch On thread : First stock bedding Job

    A snap of the machining toolpaths. 159192 A snap of the sketch I used to get the heights correct. 159193 Next I cleaned out the height references I left in for gluing the pillars in place and...

    Liked On: 30-01-2021, 11:54 AM

15. 
    Micky Duck liked post by Skirch On thread : First stock bedding Job

    So I took a whole bunch of measurements and started drawing it up in CAD to see how low I needed to set the action into the stock to get the bottom metal close enough, and the action screws to...

    Liked On: 30-01-2021, 11:53 AM

Page 7 of 8 First 12345678 Last

• Jump to page: