Snowgrass
Member

217 Likes

Page 9 of 15 First 123456789101112131415 Last

• Jump to page:

1. 
   Snowgrass liked post by 6x47 On thread : Yamaha and Honda sxs

   After doing a fair bit of research, I chose the Yammie Wolverine X2 R-Spec. The size was right and the trannie by all accounts is right up there for reliability. The 875 V-twin is quite adequate....

   Liked On: 19-05-2021, 12:38 PM

2. 
   Snowgrass liked post by Huntn On thread : Big Head Taken on Stewart Island ..?

   Your 3rd hand rumours are not to far off! Wouldn't call myself a tourist though, was there to hunt! Don't set up trail cameras but a mate did once on a trip there 4 years ago. Yes I set up a fly...

   Liked On: 09-05-2021, 05:43 PM

3. 
   Snowgrass liked post by Flyblown On thread : Hilux EGR

   I mentioned doing a vid, so here it is. I talk too much. https://www.youtube.com/watch?v=dGAyxHqHPwg

   Liked On: 13-04-2021, 11:04 AM

4. 
   Snowgrass liked post by PerazziSC3 On thread : STAGS SHOT 2021

   163710 Always good to have an alive shot to go with it

   Liked On: 29-03-2021, 09:21 AM

5. 
   Snowgrass liked post by Tahr On thread : Public Land Roar Predictions?

   Here 'tis. Shot him in close proximity to where I chased a roaroaing stag around a couple of years ago. Maybe the same stag. 162713 Shot him in the creek about 2 thirds down in this pic,...

   Liked On: 14-03-2021, 05:50 PM

6. 
   Snowgrass liked post by Tommy On thread : Stuck case stuck goodly.

   Might be an idea to polish the arse out of the inside of the die, in case there's been some galling happened when this case got stuck?

   Liked On: 03-03-2021, 06:45 PM

7. 
   Snowgrass liked post by Dicko On thread : Stuck case stuck goodly.

   In my experience with cases stuck in dies, it’s the area in front of the web towards the base that usually binds in the LGS die if you’re light on lube. If you want a very good case lube that is...

   Liked On: 02-03-2021, 06:06 PM

8. 
   Snowgrass liked post by Cordite On thread : Stuck case stuck goodly.

   Snowgrass With that screw jammed in the expander ball has to be high up in the resizing die. Mechanically, if the expander ball is too far up, that is, up in the neck area of the die, then the...

   Liked On: 02-03-2021, 01:07 PM

9. 
   Snowgrass liked post by tetawa On thread : Stuck case stuck goodly.

   It pays to clean a new FLR die with solvent before using. Manufacturers usually add a protective coating.

   Liked On: 02-03-2021, 07:06 AM

10. 
    Snowgrass liked post by flock On thread : Stuck case stuck goodly.

    I have had the same experiences, with Redding dies, they can be not so forgiving, tighter tolerances. Cheap & cheerful -----Lees dies you almost have to try to jam cases. So Well done! Kroil is...

    Liked On: 01-03-2021, 09:31 PM

11. 
    Snowgrass liked post by Micky Duck On thread : Stuck case stuck goodly.

    I use good old vasoline on body of case....just a very light smear...and the necks dipped in graphite...havent had an issue in years. pleased you got it sorted.

    Liked On: 01-03-2021, 09:31 PM

12. 
    Snowgrass liked post by mikee On thread : Stuck case stuck goodly.

    you need to be winding the nut not trying to use the press to pull it out.

    Liked On: 01-03-2021, 05:58 PM

13. 
    Snowgrass liked post by matagouri On thread : Stuck case stuck goodly.

    https://www.gunworks.co.nz/shop/category/stuck-case-remover

    Liked On: 01-03-2021, 05:58 PM

14. 
    Snowgrass liked post by dogmatix On thread : Stuck case stuck goodly.

    Squirt some lanoline case lube or WD40 down through the top of the die as well. Works a treat with Hornady F/L dies. Didn't even have to drill and tap the case.

    Liked On: 01-03-2021, 05:58 PM

15. 
    Snowgrass liked post by grandpamac On thread : Stuck case stuck goodly.

    Try putting a half inch socket over the case. Change the Phillips head screw for a bolt with some fat washers between the bolt head and the socket and tighten with a spanner. Clearly there was not...

    Liked On: 01-03-2021, 04:53 PM

Page 9 of 15 First 123456789101112131415 Last

• Jump to page: