steven
Member

1532 Likes

Page 11 of 103 First 1234567891011121314151617181920212223242561 ... Last

• Jump to page:

1. 
   steven liked post by Beavis On thread : New ADI factory & powders

   I don't understand why they can't just keep the formulation the same. I couldn't imagine a world without 2206H.

   Liked On: 22-01-2016, 12:57 PM

2. 
   steven liked post by MassiveAttack On thread : Selling a Colt AR15, what to do?

   I would keep it E cat until I sold it and change it to A if needed by the new owner. I would sell it as is but with the original parts. ARs normally start at about $1500.

   Liked On: 22-01-2016, 12:53 PM

3. 
   steven liked post by Beavis On thread : Selling a Colt AR15, what to do?

   A proper A2 upper us very desirable, less so if the barrel has been shortened. Pics?

   Liked On: 22-01-2016, 12:52 PM

4. 
   steven liked post by 300CALMAN On thread : Cast reload question

   It dosent look like your projectiles are seated too far out. Also those marks don't look much like rifling to me, looks like marks from the guide ramp or side of the chamber entrance. If you want...

   Liked On: 21-01-2016, 03:52 PM

5. 
   steven liked post by Kscott On thread : US Firearm Industries under attack!!!!!!!!

   Can we please keep the bat shit crazy conspiracy nonsence to other forums ?

   Liked On: 21-01-2016, 03:24 PM

6. 
   steven liked post by gimp On thread : US Firearm Industries under attack!!!!!!!!

   Stop copying and pasting stupid shit you get emailed you retard

   Liked On: 21-01-2016, 03:24 PM

7. 
   steven liked post by Konev On thread : 1939 Mosin Nagant

   For the Mosin, if its hex receiver then a tad more than a round, but prewar are generally in better condition than mid 40s. however i suggest you dont sell it, they are stupidly good fun.

   Liked On: 20-01-2016, 02:55 PM

8. 
   steven liked post by gadgetman On thread : Annealing questions

   Thanks Pete. Though I'm from the 60's and prefer SI units. :D

   Liked On: 16-01-2016, 02:39 PM

9. 
   steven liked post by P38 On thread : Annealing questions

   All electronic parts including the pan came from Aliexpress...

   Liked On: 16-01-2016, 12:51 PM

10. 
    steven liked post by On thread : Annealing questions

    Just be careful and watch a few YouTube clips one I watched the guy was getting the brass way to hot compared to the other clips I watched

    Liked On: 14-01-2016, 05:57 PM

11. 
    steven liked post by zimmer On thread : Annealing questions

    Yeh, crazy. YouTube is bloody dangerous. I did a test to destruction on my annealer. Using 308 CAC brass I increased the heating time from 4 secs in 1/4 sec intervals up to 8 secs. The best result...

    Liked On: 14-01-2016, 02:31 PM

12. 
    steven liked post by res On thread : Annealing questions

    A small production run could be in order, to buy a factory one is about $600!

    Liked On: 13-01-2016, 10:36 PM

13. 
    steven liked post by P38 On thread : Annealing questions

    Yep I made my own with parts from aliexpress Works bloody good too. :thumbsup: https://www.youtube.com/watch?v=0-C-i0Kr2jU Cheers

    Liked On: 13-01-2016, 10:34 PM

14. 
    steven liked post by bully On thread : Annealing questions

    Auto Annealing Machine (http://www.trademe.co.nz/sports/hunting-shooting/reloading/cases/auction-1012921600.htm)

    Liked On: 13-01-2016, 10:30 PM

15. 
    steven liked post by specweapon On thread : Automating reloading with an Arduino

    I'm going to do this to make an auto case loader, In my mind it's much simpler to do with an Arduino than with mechanical linkages. Then will expand it to cover most stages, like powder check and...

    Liked On: 13-01-2016, 09:00 PM

Page 11 of 103 First 1234567891011121314151617181920212223242561 ... Last

• Jump to page: