stevodog
Banned

484 Likes

Page 16 of 33 First ... 23456789101112131415161718192021222324252627282930 ... Last

• Jump to page:

1. 
   stevodog liked post by jakewire On thread : Walnut and blued steel,

   Frodo 1957, Thirty Aught Six, Bedded and Sissy pad put on, going to clean up the stock next,would have preferred to show afterwards but never mind.. 140643 Shoots very well, sighting in at 100...

   Liked On: 28-05-2020, 01:45 PM

2. 
   stevodog liked post by Walker On thread : Options for rebarelling old P14

   The barrels been in there for a century! You need to relieve the barrel off the action face usually in a lathe but careful use of a grinder and cut off wheel will do it. It relieves the stress off...

   Liked On: 27-05-2020, 10:21 PM

3. 
   stevodog liked post by ishoot10s On thread : Options for rebarelling old P14

   John Herbert, NZ Repeating Arms, sells Criterion P14 barrels, they match the original profile. When I bought one they were $480 ish.

   Liked On: 27-05-2020, 09:02 PM

4. 
   stevodog liked post by Flyblown On thread : 6mm Creedmoor goats and deer

   Today it's the turn of the Southern Hunter All Terrain Tactical Porcine Interceptors (SHATTPI). 140958

   Liked On: 27-05-2020, 04:56 PM

5. 
   stevodog liked post by Flyblown On thread : 6mm Creedmoor goats and deer

   Back on the farm and off up the back for a hunt. We’ve had a run of hard, heavy frosts, been deadly cold at night. But then the rain came, and the wind changed and I worked out an approach into one...

   Liked On: 25-05-2020, 10:32 PM

6. 
   stevodog liked post by john worthington On thread : Is this salvageable?

   send it to me i can sort that for you cheers john

   Liked On: 25-05-2020, 02:30 PM

7. 
   stevodog liked post by Ryan_Songhurst On thread : New boomstick... what a bloody drama

   Built off a P14

   Liked On: 24-05-2020, 10:30 PM

8. 
   stevodog liked post by nor-west On thread : 6.5x55 SE Sanity Check

   ADI and a lot of other powder makers/ distributors will quote low loadings because there still exists a lot of older pre 98 mausers. I don't load for a 6.5x55 anymore but when I did the top ADI load...

   Liked On: 24-05-2020, 08:42 AM

9. 
   stevodog liked post by rupert On thread : Sharpening a D2 knife blade: some photos, observations, and opinions

   Very interesting post. I had no idea before of the changes with different grades of finish. Excellent photos.

   Liked On: 22-05-2020, 12:39 PM

10. 
    stevodog liked post by Puffin On thread : Sharpening a D2 knife blade: some photos, observations, and opinions

    Sharpening a D2 knife blade: some photos, observations, and opinions I ended up with a couple of small chips out of the edge of my re-handled Spyderco Junction after my post-lockdown trip. The...

    Liked On: 22-05-2020, 12:39 PM

11. 
    stevodog liked post by winaa On thread : Kimber 16in 7mm08 loads

    CFE 223 will give you the best velocity. 2206H just more temp stable. Try both and go with what gives best accuracy. Personally I don't subscribe to the 1000 ft/lb theory but use 2000fps impact...

    Liked On: 19-05-2020, 11:42 AM

12. 
    stevodog liked post by Shelley On thread : Sharpener edge test

    So my final test was to cut through some rpm thick natural fibre rope, no idea what it was but it came out of a gym, the stuff you used to climb up as a kid then fall onto the hard wood floor...

    Liked On: 11-05-2020, 07:37 PM

13. 
    stevodog liked post by Ground Control On thread : Gear you wish you kinda wish you never bought..

    All the excessive gadgets and bullshit that hunting and shooting magazines convinced me I needed. About 4 years ago I realised that I was carrying about 4 times as much shit than I actually needed....

    Liked On: 06-05-2020, 09:32 AM

14. 
    stevodog liked post by MB On thread : what brand features the most in your fleet

    You're right, especially for those with large/expensive collections. On the other hand, simply being a member of this forum has it's risks in that respect. It wouldn't take a genius to work out who...

    Liked On: 04-05-2020, 08:28 AM

15. 
    stevodog liked post by 40mm On thread : Knife stropping

    i brought an old barbers strop from a junk store. it seems to take the fine burr off the back of my chisels after honing. makes a difference for sure. the apprentice tells me that they slice through...

    Liked On: 03-05-2020, 08:18 AM

Page 16 of 33 First ... 23456789101112131415161718192021222324252627282930 ... Last

• Jump to page: