svt40
Member

54 Likes

Page 2 of 4 First 1234 Last

• Jump to page:

1. 
   shananah liked post by svt40 On thread : Glasses and shooting

   Fought this problem for a while - have worn glasses since about age 5 or 6 (bad astigmatism / short sighted). never knew otherwise. Went to progressive glasses around age 40 as vision deteriorated...

   Liked On: 11-01-2024, 06:15 PM

2. 
   bobbydazzler liked post by svt40 On thread : Glasses and shooting

   Fought this problem for a while - have worn glasses since about age 5 or 6 (bad astigmatism / short sighted). never knew otherwise. Went to progressive glasses around age 40 as vision deteriorated...

   Liked On: 07-01-2024, 11:02 AM

3. 
   Micky Duck liked post by svt40 On thread : Glasses and shooting

   Fought this problem for a while - have worn glasses since about age 5 or 6 (bad astigmatism / short sighted). never knew otherwise. Went to progressive glasses around age 40 as vision deteriorated...

   Liked On: 05-01-2024, 03:23 PM

4. 
   trooper90 liked post by svt40 On thread : Glasses and shooting

   Fought this problem for a while - have worn glasses since about age 5 or 6 (bad astigmatism / short sighted). never knew otherwise. Went to progressive glasses around age 40 as vision deteriorated...

   Liked On: 05-01-2024, 10:23 AM

5. 
   Marty Henry liked post by svt40 On thread : Glasses and shooting

   Fought this problem for a while - have worn glasses since about age 5 or 6 (bad astigmatism / short sighted). never knew otherwise. Went to progressive glasses around age 40 as vision deteriorated...

   Liked On: 05-01-2024, 09:35 AM

6. 
   Micky Duck liked post by svt40 On thread : Beginner question: Using pistol projectile for 7.62x54r?

   I think M-H is on the money - those lead bullets are probably expecting to see 1600 fps. With a generous burn of 2208 youre probably spraying near-molten lead out the end of the mosin at 3000 fps....

   Liked On: 16-11-2023, 04:04 PM

7. 
   schwen liked post by svt40 On thread : Bolt forced open

   Seems likely that if the bolt was opening from the chamber pressure then it would have been a much more exciting event youd be talking about. This is theoretical - but it seems plausible that the...

   Liked On: 12-10-2023, 07:04 AM

8. 
   Floundering Around liked post by svt40 On thread : Mosin Nagant Refinishing

   This.... i refinished a couple mosins with shellac, although from memory i used alcohol (meths) as the solvent for the shellac flakes. Wiped most of the old finish off with alcohol in the bathtub,...

   Liked On: 04-10-2023, 09:19 AM

9. 
   blip liked post by svt40 On thread : Mosin Nagant Refinishing

   Absolutely not! Completely different.

   Liked On: 30-09-2023, 02:11 PM

10. 
    11mms liked post by svt40 On thread : Ruger 10/22 wont cycle

    This may help - a considerable portion of the resistance to your initial bolt movement is due to resetting the hammer. Compare cycling the bolt by hand with the rifle cocked / uncocked. Other...

    Liked On: 28-08-2023, 10:51 AM

11. 
    Jusepy liked post by svt40 On thread : small bore shooting manawatu area

    If youre considering small bore shooting with a 10/22, which is more automated and less 'refined'....ah...expensive than the usual small bore apparatus, you could consider the service rifle group...

    Liked On: 31-07-2023, 08:48 PM

12. 
    csmiffy liked post by svt40 On thread : Would you buy a .22 WSM?

    Shower thoughts have turned to the same idea - necking up 17wsm to 20 or 22. A 20wsm seemed like a good idea - the 40gr .20 projectile at 2800fps would be worth a look. plus you could use it in a...

    Liked On: 29-07-2023, 06:09 PM

13. 
    Micky Duck liked post by svt40 On thread : Would you buy a .22 WSM?

    Shower thoughts have turned to the same idea - necking up 17wsm to 20 or 22. A 20wsm seemed like a good idea - the 40gr .20 projectile at 2800fps would be worth a look. plus you could use it in a...

    Liked On: 29-07-2023, 11:38 AM

14. 
    Moa Hunter liked post by svt40 On thread : Oversteer

    A bit of play in the diff isnt necessarily an issue. Ive seen some that manage at least a half turn of one wheel before all the slack gets taken up and the other starts moving - check that it moves...

    Liked On: 16-07-2023, 10:17 PM

15. 
    Micky Duck liked post by svt40 On thread : We really are different!

    Theres a culture of 'how can i make something to do that?' here, whereas i think the overseas, particularly the USA thought process is more only 'what can i buy?'

    Liked On: 16-07-2023, 09:16 PM

Page 2 of 4 First 1234 Last

• Jump to page: