T.FOYE
Member

381 Likes

Page 12 of 26 First 1234567891011121314151617181920212223242526 Last

• Jump to page:

1. 
   Micky Duck liked post by T.FOYE On thread : Cast Lead Thread ?

   Two coats of white blue mix and a resize to .459". Good accuracy and doing 1800fts. 205920

   Liked On: 13-09-2022, 10:03 PM

2. 
   Micky Duck liked post by T.FOYE On thread : Cast Lead Thread ?

   Awesome mould. Bit of faff setting up the hole makers as they came completely disassembled but they just screw together. Bullets came out well. It's got one of those spring washers so the tension...

   Liked On: 13-09-2022, 10:03 PM

3. 
   Bill999 liked post by T.FOYE On thread : Cast Lead Thread ?

   Awesome mould. Bit of faff setting up the hole makers as they came completely disassembled but they just screw together. Bullets came out well. It's got one of those spring washers so the tension...

   Liked On: 08-09-2022, 10:59 AM

4. 
   Grey Kiwi liked post by T.FOYE On thread : Cast Lead Thread ?

   Awesome mould. Bit of faff setting up the hole makers as they came completely disassembled but they just screw together. Bullets came out well. It's got one of those spring washers so the tension...

   Liked On: 07-09-2022, 04:10 PM

5. 
   tikka liked post by T.FOYE On thread : Cast Lead Thread ?

   Awesome mould. Bit of faff setting up the hole makers as they came completely disassembled but they just screw together. Bullets came out well. It's got one of those spring washers so the tension...

   Liked On: 07-09-2022, 01:50 PM

6. 
   JD300 liked post by T.FOYE On thread : Cast Lead Thread ?

   Awesome mould. Bit of faff setting up the hole makers as they came completely disassembled but they just screw together. Bullets came out well. It's got one of those spring washers so the tension...

   Liked On: 06-09-2022, 10:10 PM

7. 
   Jhon liked post by T.FOYE On thread : Cast Lead Thread ?

   205445 Only problem... raining outside so I can't fire up the melter

   Liked On: 06-09-2022, 09:50 AM

8. 
   Micky Duck liked post by T.FOYE On thread : Cast Lead Thread ?

   205445 Only problem... raining outside so I can't fire up the melter

   Liked On: 05-09-2022, 09:07 PM

9. 
   No.3 liked post by T.FOYE On thread : Cast Lead Thread ?

   I found I was making good bullets while I was regularly fluxing and skimming off the dross. Keep it mixing. Don't let your top screw on your lee melter wind out too much (less is more). It's a good...

   Liked On: 05-09-2022, 05:45 PM

10. 
    JD300 liked post by T.FOYE On thread : Cast Lead Thread ?

    Those laser thermos are good for the outside but you wanna reading from down in the mix. I got this one for $35usd plus $10 postage. Arrived in less than a week ...

    Liked On: 04-09-2022, 01:26 PM

11. 
    Micky Duck liked post by T.FOYE On thread : Cast Lead Thread ?

    Am very much looking fwd to this arriving soon. It's the only hollowpoint mould MP has in stock atm for the .458 fans. They do have a more sleek model but it's on backorder (and makes a lighter...

    Liked On: 02-09-2022, 09:54 PM

12. 
    Micky Duck liked post by T.FOYE On thread : Cast Lead Thread ?

    I found I was making good bullets while I was regularly fluxing and skimming off the dross. Keep it mixing. Don't let your top screw on your lee melter wind out too much (less is more). It's a good...

    Liked On: 02-09-2022, 09:54 PM

13. 
    JD300 liked post by T.FOYE On thread : Cast Lead Thread ?

    Am very much looking fwd to this arriving soon. It's the only hollowpoint mould MP has in stock atm for the .458 fans. They do have a more sleek model but it's on backorder (and makes a lighter...

    Liked On: 02-09-2022, 10:54 AM

14. 
    JD300 liked post by T.FOYE On thread : Cast Lead Thread ?

    Check Amazon eh. I got a lyman electronic one with a probe and it does the job well. Really cheap too considering what it does

    Liked On: 02-09-2022, 10:54 AM

15. 
    JD300 liked post by T.FOYE On thread : Cast Lead Thread ?

    I found I was making good bullets while I was regularly fluxing and skimming off the dross. Keep it mixing. Don't let your top screw on your lee melter wind out too much (less is more). It's a good...

    Liked On: 02-09-2022, 10:54 AM

Page 12 of 26 First 1234567891011121314151617181920212223242526 Last

• Jump to page: