T.FOYE
Member

337 Likes

Page 7 of 23 First 123456789101112131415161718192021 ... Last

• Jump to page:

1. 
   T.FOYE liked post by southernman On thread : Powder throwers

   If you can afford it a Harrell's precision powder thrower, is the best you can get, is unaffected, by drafts, battery's, vibration etc. and is easy to adjust and repeatable, This is what Most bench...

   Liked On: 30-08-2023, 05:24 PM

2. 
   T.FOYE liked post by Micky Duck On thread : DIY bullet tips for flat nosed cast bullets

   yip BB into hollow point. if you already have a centred hollow point its too easy to enlarge it a WEE bit with 7mm drill bit so BB sits in nice and securely. bit hit and miss with a flat point,hard...

   Liked On: 18-07-2023, 12:06 AM

3. 
   T.FOYE liked post by makka On thread : DIY bullet tips for flat nosed cast bullets

   I'm firing up the printer to do some softbait molds, will do a few test BT's for you at the same time

   Liked On: 14-07-2023, 12:48 PM

4. 
   T.FOYE liked post by blip On thread : Trimming brass

   Ive got a weird one. 3 6.5x55s the two military ones never seem to need trimming but using similar load in my t3 it always seems to need a trim. I use a lee hand case trimmer

   Liked On: 07-07-2023, 11:31 PM

5. 
   T.FOYE liked post by Micky Duck On thread : Trimming brass

   look at partial length resizing...it might help. by not shrinking brass so much it has to enlarge less upon firing .

   Liked On: 07-07-2023, 11:30 PM

6. 
   T.FOYE liked post by csmiffy On thread : Useing the firearms register

   They struggled to maintain an accurate registry back in the 80s and didn't include all firearms. Tring to do this now with gun parts makes it exponentially harder. Just because the numpties wanted...

   Liked On: 04-07-2023, 02:02 PM

7. 
   T.FOYE liked post by Moutere On thread : Tikka T3X barrel break-in

   Exactly. Dedicated traditional break in at a range is more or less a waste of time. Especially on the OPs T3

   Liked On: 03-07-2023, 06:58 AM

8. 
   T.FOYE liked post by Waimauku On thread : Case Neck runout with redding type s bushing die

   Was getting similar result with my type s die, 3-4 thou was common and that is neck turned and then annealed.My competition redding die was no better. Tried a redding FL die and that was more often...

   Liked On: 03-07-2023, 06:47 AM

9. 
   T.FOYE liked post by gimp On thread : The Four Stages of Handloading Competence

   1. Hey I can load ammo cheaper than factory 2. Hey I can make really accurate loads 3. Hey this is fun 4. Oh my god I'm sick to death of doing this punishing repetitive activity, I want a 6.5CM...

   Liked On: 29-06-2023, 10:43 PM

10. 
    T.FOYE liked post by grandpamac On thread : DIY bullet tips for flat nosed cast bullets

    The biggest difference might be that they shoot like shit. GPM.

    Liked On: 17-06-2023, 10:30 PM

11. 
    T.FOYE liked post by makka On thread : DIY bullet tips for flat nosed cast bullets

    I was thinking about 3d printing some the other day, using a resin printer so failing under high temp shouldn't be an issue

    Liked On: 17-06-2023, 10:19 PM

12. 
    T.FOYE liked post by 7mmsaum On thread : DIY bullet tips for flat nosed cast bullets

    Used to put Bic pen nibs in Berger VLD years ago :) Hot melt glue would work in those cast slugs Then spin them up and machine with a sanding block Consider having a central shaft...

    Liked On: 16-06-2023, 11:14 PM

13. 
    T.FOYE liked post by akaroa1 On thread : DIY bullet tips for flat nosed cast bullets

    Oh dear someone has gone down a deep dark hole

    Liked On: 16-06-2023, 11:02 PM

14. 
    T.FOYE liked post by Avopik On thread : 45/70 Action Strengths

    Hiya; a question….. there’s 3 different load parameters for 45/70 rifles . Reasonably mild load data for “ Trapdoor “ actions, pretty reasonable load data for lever actions & Grunty load data for “...

    Liked On: 11-06-2023, 09:30 PM

15. 
    T.FOYE liked post by -BW- On thread : Some help pricing some items for sale from deceased estate

    Now you're being silly dude. Firstly I already own a pile of reloading gear, and I don't shoot .308. I bought the powder and primers they had and gave them $400 for a start. They will get cash for...

    Liked On: 25-05-2023, 07:49 AM

Page 7 of 23 First 123456789101112131415161718192021 ... Last

• Jump to page: