Tararua Phil
Member

97 Likes

Page 1 of 7 1234567 Last

• Jump to page:

1. 
   Bryan liked post by Tararua Phil On thread : Pistol case making & reloading the India/Pakistan way.

   I Just thought you'd enjoy the careful manufacturing & reloading example portrayed in this vid I found. I wouldn't advise buying ammo from these guys. My reloading efforts don't seem so bad after...

   Liked On: 17-03-2025, 01:39 PM

2. 
   nevereadyfreddy liked post by Tararua Phil On thread : Pistol case making & reloading the India/Pakistan way.

   I Just thought you'd enjoy the careful manufacturing & reloading example portrayed in this vid I found. I wouldn't advise buying ammo from these guys. My reloading efforts don't seem so bad after...

   Liked On: 17-03-2025, 05:31 AM

3. 
   Brian liked post by Tararua Phil On thread : Pistol case making & reloading the India/Pakistan way.

   I Just thought you'd enjoy the careful manufacturing & reloading example portrayed in this vid I found. I wouldn't advise buying ammo from these guys. My reloading efforts don't seem so bad after...

   Liked On: 13-03-2025, 09:55 AM

4. 
   Micky Duck liked post by Tararua Phil On thread : The 8 x 60

   In order to down size the neck, how about removing the decap pin stem so it only sizes the outside. Perhaps the inside dia would now be closer to what you need; after all the decap ball is what sizes...

   Liked On: 08-03-2025, 09:41 AM

5. 
   Lucky liked post by Tararua Phil On thread : The 8 x 60

   In order to down size the neck, how about removing the decap pin stem so it only sizes the outside. Perhaps the inside dia would now be closer to what you need; after all the decap ball is what sizes...

   Liked On: 05-03-2025, 02:10 PM

6. 
   Growlybear liked post by Tararua Phil On thread : Rabbits and Hares close to houses

   Or air rifle.

   Liked On: 27-12-2024, 11:26 PM

7. 
   John Duxbury liked post by Tararua Phil On thread : A New Mistake...

   With the stuck case...With the proper case holder in place, can you wind out the die a few turns then raise the ram until the stripped part of the case rim enters the proper case holder, then rotate...

   Liked On: 31-10-2024, 05:07 PM

8. 
   Micky Duck liked post by Tararua Phil On thread : A New Mistake...

   With the stuck case...With the proper case holder in place, can you wind out the die a few turns then raise the ram until the stripped part of the case rim enters the proper case holder, then rotate...

   Liked On: 31-10-2024, 04:03 PM

9. 
   dannyb liked post by Tararua Phil On thread : A New Mistake...

   With the stuck case...With the proper case holder in place, can you wind out the die a few turns then raise the ram until the stripped part of the case rim enters the proper case holder, then rotate...

   Liked On: 31-10-2024, 03:10 PM

10. 
    No.3 liked post by Tararua Phil On thread : A New Mistake...

    With the stuck case...With the proper case holder in place, can you wind out the die a few turns then raise the ram until the stripped part of the case rim enters the proper case holder, then rotate...

    Liked On: 31-10-2024, 02:16 PM

11. 
    ZQLewis liked post by Tararua Phil On thread : .308 subsonic load

    Try this vid as a basis & see how you get on. There's a part 1-3 https://www.youtube.com/watch?v=DB1DpwMth98

    Liked On: 07-09-2024, 07:20 PM

12. 
    Jhon liked post by Tararua Phil On thread : Identify 7.62x39 Ammo

    The Chinese???? steel(1981) will be corrosive but the German MEN brass(1985) will not. Both will be Berdan primed I'd say.

    Liked On: 05-09-2024, 11:10 AM

13. 
    Glenshee liked post by Tararua Phil On thread : 6.5 Grendel PPU

    Worked well in my Howa mini but now reload with steel cases & 90gn TNT's.

    Liked On: 22-07-2024, 02:09 PM

14. 
    Ranger 888 liked post by Tararua Phil On thread : Upgrading varmint rig

    Do you honestly think it's big enough???? The buck possums can be hard to kill.

    Liked On: 29-06-2024, 02:00 AM

15. 
    yeah_na_missed liked post by Tararua Phil On thread : A Day At Work With Dad

    Excellent experience for the young fella. He's enjoying it all....see his eyes.

    Liked On: 18-05-2024, 05:01 PM

Page 1 of 7 1234567 Last

• Jump to page: