tibo
Member

261 Likes

Page 3 of 18 First 1234567891011121314151617 ... Last

• Jump to page:

1. 
   Stocky liked post by tibo On thread : ATEC Suppressor experience, problems, and troubleshooting thread

   Another thing clean your atec spray crc, wd40 on baffle ect. They corrode quite fast inside otherwise, faster than my other suppressor.

   Liked On: 17-09-2024, 10:11 PM

2. 
   mikee liked post by tibo On thread : ATEC Suppressor experience, problems, and troubleshooting thread

   Another thing clean your atec spray crc, wd40 on baffle ect. They corrode quite fast inside otherwise, faster than my other suppressor.

   Liked On: 17-09-2024, 09:38 PM

3. 
   Shamus_ liked post by tibo On thread : ATEC Suppressor experience, problems, and troubleshooting thread

   I was only having POI moving between session as I was probably not tightening it enough and consistently

   Liked On: 17-09-2024, 07:46 PM

4. 
   DPT liked post by tibo On thread : DPT brake end cap

   259354 It’s just not a fair comparison, not the same volume the Atec h2 is massive, doesnt go over barrel has much ect. The dpt offer a much more compact option and still offer enough hear...

   Liked On: 17-09-2024, 07:30 PM

5. 
   Stocky liked post by tibo On thread : ATEC Suppressor experience, problems, and troubleshooting thread

   I was only having POI moving between session as I was probably not tightening it enough and consistently

   Liked On: 17-09-2024, 07:19 PM

6. 
   Jukes liked post by tibo On thread : My 7mm PRC is driving me nuts…

   Well well well… Found the issue… one of the last thing I had to try, use virgin brass. I think this hot load I was firing hammered the brass and they were toasted after 6 firing. The primer pocket...

   Liked On: 17-09-2024, 05:34 PM

7. 
   Stocky liked post by tibo On thread : DPT brake end cap

   Didn’t pay attention between shot, A-lock system got loose and supressor launched down range 120m to beat… had also point of impact moving slightly around between shooting session depending how hard...

   Liked On: 17-09-2024, 02:09 PM

8. 
   Fisherman liked post by tibo On thread : DPT brake end cap

   I have the a-tec on my 7mm prc and the dpt on my 6.5 creedmoor so not a fair comparison. They both doing what they are supposed to do and on both the brake end cap is probably reducing the remaining...

   Liked On: 17-09-2024, 01:56 AM

9. 
   Roarless20 liked post by tibo On thread : My 7mm PRC is driving me nuts…

   Well well well… Found the issue… one of the last thing I had to try, use virgin brass. I think this hot load I was firing hammered the brass and they were toasted after 6 firing. The primer pocket...

   Liked On: 16-09-2024, 07:13 PM

10. 
    Micky Duck liked post by tibo On thread : My 7mm PRC is driving me nuts…

    Well well well… Found the issue… one of the last thing I had to try, use virgin brass. I think this hot load I was firing hammered the brass and they were toasted after 6 firing. The primer pocket...

    Liked On: 16-09-2024, 05:52 PM

11. 
    Micky Duck liked post by tibo On thread : My 7mm PRC is driving me nuts…

    Na no clickers

    Liked On: 16-09-2024, 05:51 PM

12. 
    Kelton liked post by tibo On thread : My 7mm PRC is driving me nuts…

    Well well well… Found the issue… one of the last thing I had to try, use virgin brass. I think this hot load I was firing hammered the brass and they were toasted after 6 firing. The primer pocket...

    Liked On: 16-09-2024, 05:49 PM

13. 
    Sika 8 liked post by tibo On thread : DPT brake end cap

    Tested the brake cap today, definitely reduced recoil. Made a bit a bigger bang however still not even close to without a can

    Liked On: 16-09-2024, 04:59 PM

14. 
    Edunn liked post by tibo On thread : My 7mm PRC is driving me nuts…

    Well well well… Found the issue… one of the last thing I had to try, use virgin brass. I think this hot load I was firing hammered the brass and they were toasted after 6 firing. The primer pocket...

    Liked On: 16-09-2024, 04:45 PM

15. 
    No.3 liked post by tibo On thread : My 7mm PRC is driving me nuts…

    Well well well… Found the issue… one of the last thing I had to try, use virgin brass. I think this hot load I was firing hammered the brass and they were toasted after 6 firing. The primer pocket...

    Liked On: 16-09-2024, 04:22 PM

Page 3 of 18 First 1234567891011121314151617 ... Last

• Jump to page: