Tikka7mm08
Member

1720 Likes

Page 10 of 115 First 12345678910111213141516171819202122232460110 ... Last

• Jump to page:

1. 
   Tikka7mm08 liked post by dannyb On thread : Tikka Veil Factory Stock Weight

   Bob has short arms too :yaeh am not durnk: well compared to me anyway :D

   Liked On: 06-08-2022, 01:12 AM

2. 
   Tikka7mm08 liked post by No.3 On thread : Ultrasonic cleaner tips please

   The propriety stuff sold as ultrasonic cleaner fluid in the US is basically just showerpower bam. Spray bottle at the supermarket... It's a citric acid and natural plant based stuff that's pretty...

   Liked On: 05-08-2022, 12:00 AM

3. 
   Tikka7mm08 liked post by Gerardo On thread : Kimber Montana 308 Load Development

   You're on form there mate! Sent from my SM-G975F using Tapatalk

   Liked On: 04-08-2022, 08:11 PM

4. 
   Tikka7mm08 liked post by Cyclops On thread : Ultrasonic cleaner tips please

   The steps I folllow Deprime inspect cases Anneal - every 5th use Full length size Ultrasonic clean oven dry at low heat (120 C), air cool on clean towel inspect cases prime, load with...

   Liked On: 04-08-2022, 01:11 PM

5. 
   Tikka7mm08 liked post by shift14 On thread : 6.5 PRC Load Development Begins

   Really enjoying this thread…. 202958 B

   Liked On: 04-08-2022, 12:55 AM

6. 
   Tikka7mm08 liked post by Magnus On thread : Ultrasonic cleaner tips please

   I've got the Lyman one and have been using the hornady cleaner that I got given with it. With the Lyman one the basket sits on the bottom of the cleaner basin and seems to stop the high frequency...

   Liked On: 03-08-2022, 07:16 PM

7. 
   Tikka7mm08 liked post by nor-west On thread : MS_SP Magnetospeed chronograph

   Not worried about poi change, will get an accurate load(s) then chrono it.

   Liked On: 03-08-2022, 02:14 PM

8. 
   Tikka7mm08 liked post by Nick-D On thread : Show me your knives

   Boning/butchers knife inspired by the old classic timber handled knives the old boy used to use. Good old classic high carbon steel, with a stabilised swamp kauri handle. Cool piece of timber that...

   Liked On: 02-08-2022, 10:51 PM

9. 
   Tikka7mm08 liked post by Pommy On thread : 6.5 PRC Load Development Begins

   It's non existent. But less non existent than Re26. Quite a bit arrived in the last ADI shipment and took a couple of weeks to get snapped up. Even with a short barrel, it can still give more...

   Liked On: 02-08-2022, 02:51 PM

10. 
    Tikka7mm08 liked post by Pommy On thread : 6.5 PRC Load Development Begins

    I've started to run low on Re26 and have gotten frustrated with erratic behaviour from it at times anyway, so just switched to AR2225... 202860 Both the last groups come in at 0.290" and 59.2gr...

    Liked On: 02-08-2022, 09:18 AM

11. 
    Tikka7mm08 liked post by sig4x4 On thread : Hydro Dipping

    202556

    Liked On: 01-08-2022, 11:26 PM

12. 
    Tikka7mm08 liked post by wsm junkie On thread : Ultrasonic cleaner tips please

    Mines just an el cheapo off TM, no degas or heater, can do 15-20 depending on case size and runs for 8mins. I do 3 cycles per batch of brass so 24mins n the water is pretty hot at the end.

    Liked On: 01-08-2022, 10:48 PM

13. 
    Tikka7mm08 liked post by wsm junkie On thread : Ultrasonic cleaner tips please

    I just lay them on a tea towel, cover with other half and roll them. Then grab the missus hair dryer n give each one a blast on the inside then finish them off in the tumbler

    Liked On: 01-08-2022, 09:56 PM

14. 
    Tikka7mm08 liked post by wsm junkie On thread : Ultrasonic cleaner tips please

    This is my process 1. Anneal 2. Size/deprime 3. Sonic clean 4. Dry 5. Tumble (i like shiney brass) 6. Load em up. I found a mix on an old post on here, 1/2 teaspoon citric acid

    Liked On: 01-08-2022, 09:34 PM

15. 
    Tikka7mm08 liked post by Bill999 On thread : Tikka Veil Factory Stock Weight

    the reason you get carbonfiber stocks is for the cool factor, I mean for the structural rigidity and nah I had it right the first time. looking at a carbon stock beside a tikka stock on my carpet...

    Liked On: 01-08-2022, 12:02 PM

Page 10 of 115 First 12345678910111213141516171819202122232460110 ... Last

• Jump to page: