Tikka7mm08
Member

1716 Likes

Page 32 of 115 First ... 181920212223242526272829303132333435363738394041424344454682 ... Last

• Jump to page:

1. 
   Tikka7mm08 liked post by MSL On thread : Kimber Montana Ascent 280AI Load Development

   Barrel will be toast by the time you settle on a load Sent from my iPhone using Tapatalk

   Liked On: 11-04-2021, 10:05 AM

2. 
   Tikka7mm08 liked post by Dreamer On thread : Blacklanz vs Javlin

   I’ve had my backlanz for sometime now and have just brought a rifle with a javelin bipod. Compared to the backlanz it’s pretty limited on adjustment just height some pan and tilt. I can’t see myself...

   Liked On: 10-04-2021, 11:49 PM

3. 
   Tikka7mm08 liked post by Pushover On thread : So if I start reloading

   I found utube clips helpful for die setup. You should measure the chamber length but I often just load to easy mag length for hunting loads. Chamber a case after sizing to make sure it fits ok. ...

   Liked On: 10-04-2021, 07:46 PM

4. 
   Tikka7mm08 liked post by Shelley On thread : Show me your knives

   When is ivory not ivory, when it’s elforyn, a German product made specifically to replicate ivory without the killing of elephants and the yellowing that ivory goes through over time. Used now every...

   Liked On: 08-04-2021, 02:22 PM

5. 
   Tikka7mm08 liked post by Bill999 On thread : Kimber's Hunter model Pros/Cons

   the extractor will click past if you drop a round in just fine on the montanas the three I have all do this without complaint I dont know the story with the mag fed ones

   Liked On: 08-04-2021, 12:59 PM

6. 
   Tikka7mm08 liked post by Cigar On thread : So if I start reloading

   And they obviously have made it to a decent age without blowing themselves up with bad ammo. It’s even better if they still have all their fingers...

   Liked On: 08-04-2021, 11:35 AM

7. 
   Tikka7mm08 liked post by Marty Henry On thread : So if I start reloading

   The mentoring idea is excellent, especially if he lives close you can use his kit while you work out what you want, that's how I got started. The bugger also got me hooked on bullet casting and black...

   Liked On: 08-04-2021, 11:35 AM

8. 
   Tikka7mm08 liked post by grandpamac On thread : So if I start reloading

   Greetings Remmodel7, First step is to find a mentor who will take you through the basic handloading techniques and equipment. Mentors with grey hair are preferred as they have more time and don't...

   Liked On: 08-04-2021, 10:29 AM

9. 
   Tikka7mm08 liked post by veitnamcam On thread : So if I start reloading

   I am not familiar with the breach lock kit so dont know what is in there but to answer your question as best I can. Two die set of full lenght sizing and seating die is fine for most situations....

   Liked On: 08-04-2021, 10:28 AM

10. 
    Tikka7mm08 liked post by PaulNZ On thread : Warthog Knife Sharpener Question

    Well, I've just ordered the Spyderco gauntlet with the CBN and fine ceramic rods. Hopefully it's a good thing.

    Liked On: 07-04-2021, 02:09 PM

11. 
    Tikka7mm08 liked post by veitnamcam On thread : Reloading .308

    If you are looking to save money stop right now. If you are looking to improve the performance of your rifle reloading 308 really is one of the best calibers out there....so much projectile choice...

    Liked On: 07-04-2021, 01:17 PM

12. 
    Tikka7mm08 liked post by Gkp On thread : Kimber Montana 308 Load Development

    They like to jump

    Liked On: 05-04-2021, 06:05 PM

13. 
    Tikka7mm08 liked post by Nugget connaisseur On thread : Problem with brass

    I had a similar problem with my old 308, Turned out the brass i was given had a larger diameter base. I would start by measuring one piece of brass that chambers and one that doesn't. Draw a...

    Liked On: 05-04-2021, 02:48 PM

14. 
    Tikka7mm08 liked post by Deereman On thread : New rifle problem

    Problem solved, used brand new and once fired brass and there was no problems at all. I guess my old brass has sent it’s last sending. Lol

    Liked On: 04-04-2021, 04:46 PM

15. 
    Tikka7mm08 liked post by viper On thread : Show me your knives

    163981 Having a run off high carbon hunting knife orders atm . This one is just finished and off to a Central Otago hunter. Viper model in 1084 , forced patina and a very light stone wash. Full...

    Liked On: 03-04-2021, 12:38 PM

Page 32 of 115 First ... 181920212223242526272829303132333435363738394041424344454682 ... Last

• Jump to page: