veitnamcam
Almost literate.

33630 Likes

Page 286 of 2242 First ... 1862362722732742752762772782792802812822832842852862872882892902912922932942952962972982993003363867861286 ... Last

• Jump to page:

1. 
   veitnamcam liked post by PerazziSC3 On thread : 7saum vs 280ai vs 7blaser vs?

   Because it's not 1906? :D

   Liked On: 28-05-2022, 05:11 PM

2. 
   veitnamcam liked post by stug On thread : "Too pretty to use"

   One of the boys I taught had a grandfather that ordered a Browning shotgun from Belgium. He died before he shotgun turned up. When the family received the shotgun they chucked it on the tractor and...

   Liked On: 28-05-2022, 05:08 PM

3. 
   veitnamcam liked post by PerazziSC3 On thread : 7saum vs 280ai vs 7blaser vs?

   Pretty much, walked into one shop and purchased everything I needed. I've had a 7mm rem mag, 7mmsaum, 280ai (2x), 300wsm, 300 win plus many other magnums that all roughly do about the same thing....

   Liked On: 28-05-2022, 03:03 PM

4. 
   veitnamcam liked post by Micky Duck On thread : 223 on deer

   take it off the other end and fit a slip on recoil pad maybe????

   Liked On: 28-05-2022, 02:53 PM

5. 
   veitnamcam liked post by mikee On thread : 223 on deer

   you need a bigger boat perhaps??

   Liked On: 28-05-2022, 02:48 PM

6. 
   veitnamcam liked post by PerazziSC3 On thread : 7saum vs 280ai vs 7blaser vs?

   197851 Going 6.5 PRC. Will get a trueflite barrel screwed into one of these 197852

   Liked On: 28-05-2022, 12:19 PM

7. 
   veitnamcam liked post by 7mmsaum On thread : 7saum vs 280ai vs 7blaser vs?

   There’s three packets of Nosler saum brass in invercargil and lots of ADG with our friendly forum advertiser And there’s any amount hoarded around NZ I know where there’s 5 packets of brand...

   Liked On: 28-05-2022, 12:18 PM

8. 
   veitnamcam liked post by PerazziSC3 On thread : 7saum vs 280ai vs 7blaser vs?

   Now I'm thinking 6.5prc... brass easy to get, still packs enough punch to 600m

   Liked On: 28-05-2022, 12:15 PM

9. 
   veitnamcam liked post by Martin358 On thread : 8.6blk - anyone here in nz have one....

   dead eye dicks made me a 338 whisper about 12 years ago. Very quiet and with the 300 g bullet the deer just looked up when hit walked a couple steps and fell over. The bullet tumbled in side and made...

   Liked On: 28-05-2022, 09:16 AM

10. 
    veitnamcam liked post by caberslash On thread : 223 on deer

    I'd cut the boat instead... :ORLY:

    Liked On: 28-05-2022, 08:33 AM

11. 
    veitnamcam liked post by Woody On thread : Needed a new lockable case for my ftr rifle

    Planed down some lawson cypress boards to required dimensions and glued and screwed all joints. Then traced outline of rifle inside and cut compartments to fit. Used 12mm rubber mats cut to fit...

    Liked On: 27-05-2022, 08:54 PM

12. 
    veitnamcam liked post by 40mm On thread : Fun looking air rifle

    Yup, and he will learn to be a better shot with asingle shot. Save the semi for when he has mastered the single shot :)

    Liked On: 27-05-2022, 08:51 PM

13. 
    veitnamcam liked post by imaca On thread : Fun looking air rifle

    Just get a springer. You are setting yourself (or your son) up for the hassle and cost of replacing co2 cartridges all the time. I've still got and use my BSA meteor that I was given 43 years ago

    Liked On: 27-05-2022, 08:50 PM

14. 
    veitnamcam liked post by Tahr On thread : 223 on deer

    Just me, but for an all round .223 I wouldn't want under 20". 20" is the ideal for me (I have 2 20", and a 22"). The folk with shorter barrels always seem to be chasing velocity. My theoretical...

    Liked On: 27-05-2022, 08:09 PM

15. 
    veitnamcam liked post by stagstalker On thread : 6.5prc

    Just typical of factory ammo really. You can find comfort in knowing if you shot the same brand of ammo in a lesser calibre say a 6.5cm then it would still be slower so you still have the gain over...

    Liked On: 27-05-2022, 01:34 AM

Page 286 of 2242 First ... 1862362722732742752762772782792802812822832842852862872882892902912922932942952962972982993003363867861286 ... Last

• Jump to page: