veitnamcam
Almost literate.

33526 Likes

Page 355 of 2236 First ... 2553053413423433443453463473483493503513523533543553563573583593603613623633643653663673683694054558551355 ... Last

• Jump to page:

1. 
   veitnamcam liked post by XR500 On thread : She,s a real hotty.

   Xmas 1983 in South Australia: pulled a 10 day shift during the closedown period maintaining the crusher and ball mill at Mt Gunson copper mine (just south of Woomera). 55 degrees at 3pm, 6 days in a...

   Liked On: 28-12-2021, 10:20 PM

2. 
   veitnamcam liked post by nor-west On thread : She,s a real hotty.

   Only that! 44 here in North Perth.

   Liked On: 28-12-2021, 10:19 PM

3. 
   veitnamcam liked post by Micky Duck On thread : Big Bronzie surfcasting of the beach...i did it!!

   Im guessing your cutting barb off bit is meaning cutting fishes barb off??? in which case agree 100% and pretty sure Steve Irwin would do so too....

   Liked On: 28-12-2021, 09:57 PM

4. 
   veitnamcam liked post by Roarless20 On thread : Sighting with factory and handloads

   I like shooting with a bipod but ALWAYS leave it folded up and rest it on a bush shirt or something when firing over the ute bonnet. The bipod will bounce/rebound badly as the bonnet will 'bounce'...

   Liked On: 28-12-2021, 08:54 PM

5. 
   veitnamcam liked post by Micky Duck On thread : Sighting with factory and handloads

   all good bud....prone is always best....you can get away with a sleeping bag in its cover/cushion...day bag with old swannie inside it is ideal....if you have and use bipod..consider trying something...

   Liked On: 28-12-2021, 08:41 PM

6. 
   veitnamcam liked post by Russian 22. On thread : bedding issues

   ok, it just appears that the front is ok height wise but the rear is too high as it has a Parker Hale trigger and not the standard M98 one. i'll redo it all and see how it goes.

   Liked On: 28-12-2021, 08:36 PM

7. 
   veitnamcam liked post by Husky1600 On thread : bedding issues

   Take material out over the whole bedding job, not just the rear tang. Route it all out to your hearts content, install some simple pillars in the action screw holes so that its all to the right depth...

   Liked On: 28-12-2021, 08:15 PM

8. 
   veitnamcam liked post by scotty On thread : bedding issues

   like i said trying to squeeze a large ring action into a small ring stock........ rout it out ..........will need shorter action screws too

   Liked On: 28-12-2021, 08:14 PM

9. 
   veitnamcam liked post by charliehorse On thread : Point Blank

   Headed up the bush 2 days before Xmas for an evening hunt with the calibre of all calibres at my side:thumbsup: Would probably be my last for a few weeks. Went up after dinner and was on the...

   Liked On: 28-12-2021, 04:35 PM

10. 
    veitnamcam liked post by stingray On thread : Fishing tomorrow!

    186708 Now I’m not one to gossip , but got a PM from a veteran fisherman, with the above photos …I comment they look like good keepers , then says …errr I may have being measuring them wrong and...

    Liked On: 28-12-2021, 04:24 PM

11. 
    veitnamcam liked post by Woody On thread : Sighting with factory and handloads

    Fair enough but first you need to prove the loads.

    Liked On: 28-12-2021, 03:51 PM

12. 
    veitnamcam liked post by deer243 On thread : Big Bronzie surfcasting of the beach...i did it!!

    Had a awesome night surfcasting for for big sharks of the beach last night. Set up with a Shadow X 13foot, Penn 9500ss spooled with 400m of 30lb line. Used a 310lb mono trace with a 16/0 cirlce...

    Liked On: 28-12-2021, 03:27 PM

13. 
    veitnamcam liked post by Nick-D On thread : Best way to sharpen Mercator Stainless?

    Sharpen to whatever angle you like man, a lower angle will cut longer but deform quicker against hard surfaces like bone. The lansky systems the angle is only approximate anyway as its deferent...

    Liked On: 27-12-2021, 10:31 PM

14. 
    veitnamcam liked post by Brian On thread : Faulty Backlanzn attachment?

    Worked good for a couple of roos but I soon got sick of carrying it in one hand and a rifle in the other.

    Liked On: 27-12-2021, 10:30 PM

15. 
    veitnamcam liked post by burtonator On thread : Faulty Backlanzn attachment?

    I’ve put mine through it’s paces and haven’t had any issues to speak of :)

    Liked On: 27-12-2021, 10:29 PM

Page 355 of 2236 First ... 2553053413423433443453463473483493503513523533543553563573583593603613623633643653663673683694054558551355 ... Last

• Jump to page: