veitnamcam
Almost literate.

33526 Likes

Page 507 of 2236 First ... 740745749349449549649749849950050150250350450550650750850951051151251351451551651751851952052155760710071507 ... Last

• Jump to page:

1. 
   veitnamcam liked post by Got-ya On thread : Kontiki catch

   All caught using mullet which I catch in the Waikato river. I normally salt it then freeze it to prolong shelf life. The salting is more to toughen the baits, not for its increased keeping abilities....

   Liked On: 13-04-2021, 05:44 PM

2. 
   veitnamcam liked post by grandpamac On thread : 25-06 why hasn't it achieved fame and success in New Zealand?

   Greetings 257 Weatherby and All, I didn't say the .25-06 is not a good cartridge but that it was not popular due to the reasons I outlined. I just checked the current offerings from Reloaders and...

   Liked On: 13-04-2021, 05:26 PM

3. 
   veitnamcam liked post by MB On thread : Freedom camping meets Nashes ban hammer.

   A bit like guns, the problem is with the people not the vehicle. If they don't give a shit to the point that they're leaving their shit all over the place, a self-contained van isn't going to help....

   Liked On: 13-04-2021, 04:49 PM

4. 
   veitnamcam liked post by zimmer On thread : Fast twist barrels

   Here’s article from Accurate Shooter on the topic Twist versus Velocities. How Muzzle Velocity Changes with Different Barrel Twist Rates « Daily Bulletin...

   Liked On: 13-04-2021, 10:47 AM

5. 
   veitnamcam liked post by Stocky On thread : Fast twist barrels

   Not quite that assumes that all energy from burnt powder is instantly passed on to the projectile but realistically it has intertia and take time to accelerate similar to dropping a bullet from a...

   Liked On: 13-04-2021, 10:44 AM

6. 
   veitnamcam liked post by Savage1 On thread : Advice for Northland goat hunter going after Kaweka sika

   From what I've experienced, its best to have a mate operating the caller and staying put while you sneak in on them as they often roar but don't move. Sika are incredible at breaking a hunters...

   Liked On: 13-04-2021, 10:32 AM

7. 
   veitnamcam liked post by A330driver On thread : Kontiki catch

   Yeah mate...good feed there for shore......well done

   Liked On: 13-04-2021, 08:43 AM

8. 
   veitnamcam liked post by Magnus On thread : So if I start reloading

   https://www.trademe.co.nz/a/marketplace/sports/hunting-shooting/reloading/presses/listing/3046139885 Have a crack at this Lyman press, try and snake the auction in the last minute. Looks old but...

   Liked On: 12-04-2021, 09:41 PM

9. 
   veitnamcam liked post by zimmer On thread : So if I start reloading

   The press is cast alloy. It wouldn't be my choice (space here for all the Lee alloy press owners to chime in), Its the bottom of the RCBS pile. I'd be looking for a good older second hand cast iron...

   Liked On: 12-04-2021, 08:44 PM

10. 
    veitnamcam liked post by Flyblown On thread : Hilux EGR

    I mentioned doing a vid, so here it is. I talk too much. https://www.youtube.com/watch?v=dGAyxHqHPwg

    Liked On: 12-04-2021, 08:30 PM

11. 
    veitnamcam liked post by Pauli On thread : EZESHARP Blade Sharpener - a quick review

    Here are my initial thoughts about the EzeSharp Blade Sharpener I purchased recently from www.kentmaster.nz. Price and delivery time were good. Initial set-up was relatively simple after viewing a...

    Liked On: 12-04-2021, 08:07 PM

12. 
    veitnamcam liked post by Shearer On thread : Bike Porn - Regardless of the motor, Show off your "two wheeled" beasties

    A few years back when MTB was my main recreation I bought a bike worth $3K. When some people, who weren't into MTB ,found out what I spent on it the said "Shit! You could have bought a car for...

    Liked On: 12-04-2021, 03:29 PM

13. 
    veitnamcam liked post by Shearer On thread : Bike Porn - Regardless of the motor, Show off your "two wheeled" beasties

    This is what I call leaning a bike over. 164962

    Liked On: 12-04-2021, 01:49 PM

14. 
    veitnamcam liked post by Woody On thread : Permatrims

    I am referring to trim angle, not depth of cavitation plate.

    Liked On: 12-04-2021, 01:46 PM

15. 
    veitnamcam liked post by grandpamac On thread : So if I start reloading

    Greetings Remmodel7, Don't get discouraged by all the complexity and sometimes contradictory advice you are getting. Handloading is only as complex as you make it. The flashy kit that some...

    Liked On: 12-04-2021, 09:31 AM

Page 507 of 2236 First ... 740745749349449549649749849950050150250350450550650750850951051151251351451551651751851952052155760710071507 ... Last

• Jump to page: