WallyR
Member

2028 Likes

Page 132 of 136 First ... 3282118119120121122123124125126127128129130131132133134135136 Last

• Jump to page:

1. 
   WallyR liked post by Maca49 On thread : Empty rimfire cases

   I plant them where they fall, will harvest the fruit next year when it gets to the right calibre!:thumbsup:

   Liked On: 13-07-2016, 09:04 PM

2. 
   WallyR liked post by Tuckerbox On thread : Today's efforts

   Needed to raise my recoil pad to get it positioned properly for prone shooting. This was the solution. http://i898.photobucket.com/albums/ac185/HarpoonKing/Mobile%20Uploads/DSC_0016_zpstjkfhvdi.jpg...

   Liked On: 13-07-2016, 08:57 PM

3. 
   WallyR liked post by veitnamcam On thread : New old lathe

   What is it? A Myford? The box of bits would be worth more than the lathe....its always the accessorys and tooling that eats up the dollars. good score.

   Liked On: 13-07-2016, 08:56 PM

4. 
   WallyR liked post by Maca49 On thread : New old lathe

   I'll donate you a 1 HP single phase motor if you need one, freights on you

   Liked On: 13-07-2016, 08:56 PM

5. 
   WallyR liked post by Timmay On thread : 260 & Barnes 130 TSX

   From my research they like a .05" jump and a decent powder load. I followed that advice in my 223 and the last 3 shot 3 different powder loads shot .8 .7 and .65" inches at 100m - the group...

   Liked On: 13-07-2016, 08:53 PM

6. 
   WallyR liked post by Ryan On thread : 7.62 x 51 CETME

   120 FPS. I shot the video using an iPhone 5S. Glycerine just noticed that it looks as if you have a toe for a thumb. :P

   Liked On: 12-07-2016, 06:40 PM

7. 
   WallyR liked post by Glycerine On thread : 7.62 x 51 CETME

   11grains of trail boss 155gr projectile.... slow-mo https://www.youtube.com/watch?v=_gSe9jWBnKE

   Liked On: 12-07-2016, 01:03 PM

8. 
   WallyR liked post by Kscott On thread : Great article on rimfire resizing and bullet comparisons

   http://www.rimfirecentral.com/rfcftp/pdfs/resizing-project.pdf These guys have been dealing with rimfire shooting for years, testing $$ cost of ammo vs resizing dies on cheap ammo vs...

   Liked On: 11-07-2016, 11:23 PM

9. 
   WallyR liked post by Friwi On thread : Is there any interest in Target shooting competitions with center fire Hunting Rifles

   We are going to try to organise a day shoot at the whatawhata range sometime early next year. I am not sure of the format yet, but it could be some gong shoot with hunting rifles. Or it could...

   Liked On: 11-07-2016, 11:06 PM

10. 
    WallyR liked post by quentin On thread : Sorting 22lr

    After reading this thread, I decided I would see if sorting my cci subs would make a blind bit of difference. A few minutes on the lathe had a sizing block made, and the dial indicator was put to...

    Liked On: 11-07-2016, 10:35 PM

11. 
    WallyR liked post by Pop Shot On thread : Smallbore shooting

    Shot it right throughout high school and didn't do too bad. It has helped significantly with all other aspects of my shooting. To be honest, might look at getting back into it. Still regret selling...

    Liked On: 11-07-2016, 10:25 PM

12. 
    WallyR liked post by Timmay On thread : RUGER PRECISION RIFLE AND RELOADS

    Unless you have the hornady Lock N load Comparator set up with the Modified cases etc you are flying blind with regards to "the lands" Short answer have a play with seating depths depending on if...

    Liked On: 11-07-2016, 09:35 PM

13. 
    WallyR liked post by On thread : wanted

    i just use my press with no die in it put your bullet in it raise it up grip the projectile with pliers and lower it after a while you should get the hang of it and not damage the projectile to much

    Liked On: 11-07-2016, 09:32 PM

14. 
    WallyR liked post by Marty Henry On thread : Powder getting thin in Auckland

    The concrete mixers getting fired up now wanna lend a hand?

    Liked On: 11-07-2016, 09:32 PM

15. 
    WallyR liked post by 7x64 On thread : Donuts in 243 necks

    Personally I wouldn't mess with brass with an unknown history. Is it really worth the hassle? And I thought I was tight! :D

    Liked On: 11-07-2016, 09:29 PM

Page 132 of 136 First ... 3282118119120121122123124125126127128129130131132133134135136 Last

• Jump to page: