WillB
Member

505 Likes

Page 25 of 34 First ... 111213141516171819202122232425262728293031323334 Last

• Jump to page:

1. 
   WillB liked post by Cigar On thread : Reloading set up

   I use ADI powders because they work and are readily available. I have used various primers over the years and never had any problems, I go with what my local shop stocks. Sierra (blitz, gameking,...

   Liked On: 01-02-2019, 07:30 PM

2. 
   WillB liked post by Monk On thread : 7mm SAUM, WSM, Blaser Magnum, Rem Mag and 284 Superpig Discussion

   Tikka 300wsm cut to 20inch,ssrnz can,running 178eld-x at 2950 with RL17.Love it104052

   Liked On: 01-02-2019, 07:23 PM

3. 
   WillB liked post by chainsaw On thread : 7mm SAUM, WSM, Blaser Magnum, Rem Mag and 284 Superpig Discussion

   My 7mm family ..... plus the odd 30cal :thumbsup: 103921

   Liked On: 01-02-2019, 07:19 PM

4. 
   WillB liked post by Max Headroom On thread : Reloading set up

   OP, I have read the thread through, and am guessing at this point, that your head will be spinning a bit. When I started, I was intimidated by how much I didn't know, and afraid of making a...

   Liked On: 31-01-2019, 09:58 PM

5. 
   WillB liked post by gonetropo On thread : Reloading set up

   u use the hornady powder dispenser and make it dispense a couple of grains below whats needed then trickle powder on to the scales. makes for a more accurate load. the dispenser is not super accurate...

   Liked On: 31-01-2019, 09:57 PM

6. 
   WillB liked post by Seventenths On thread : Reloading set up

   Shooting that many rounds per month which equals into ALOT over a year... that's ALOT of money which can be saved by reloading your own! The great thing about reloading is you get to tailor your...

   Liked On: 31-01-2019, 09:49 PM

7. 
   WillB liked post by Max Headroom On thread : Reloading set up

   Assuming an average of 30/ month, thats 360 per year approx. The reason I asked was to determine the kind of press that would likely suit you best. This will easily be done on a single stage...

   Liked On: 31-01-2019, 09:48 PM

8. 
   WillB liked post by Cordite On thread : How to Hang a Gong

   How to hang a gong 103997

   Liked On: 31-01-2019, 09:12 PM

9. 
   WillB liked post by bully On thread : How to Hang a Gong

   Two warratahs, with the chains coming off the gong, bolted. The warratahs should have a notch cut out the top, I just slip the chain link over the notch. No issues. And my gong if a big ten inch...

   Liked On: 31-01-2019, 08:12 AM

10. 
    WillB liked post by McNotty On thread : How to Hang a Gong

    Treading.... on thin ice with these terrible puns....pressure get to you?

    Liked On: 30-01-2019, 12:29 PM

11. 
    WillB liked post by Gibo On thread : How to Hang a Gong

    Still sounds tyreing

    Liked On: 30-01-2019, 12:29 PM

12. 
    WillB liked post by Gibo On thread : How to Hang a Gong

    Mate are you off your meds? No need to be polite :P

    Liked On: 30-01-2019, 12:28 PM

13. 
    WillB liked post by Cordite On thread : How to Hang a Gong

    1/1000 millisecond... But the idea is not to hit them. (-:

    Liked On: 30-01-2019, 12:27 PM

14. 
    WillB liked post by Nick-D On thread : Knives of Alaska Aloha Wolf

    Every steel will vary with different makers, flash modern steels are hard to heat treat properly. I like the blade shape, not keen on the finger choil handles though. Another option in the same...

    Liked On: 30-01-2019, 07:29 AM

15. 
    WillB liked post by High Country Boy On thread : Knives of Alaska Aloha Wolf

    Hi have one of these. The shape is good the steel is easy to sharpen. The thing I don’t like about the knife is if the handle gets covered in blood it gets very slippery.

    Liked On: 30-01-2019, 07:29 AM

Page 25 of 34 First ... 111213141516171819202122232425262728293031323334 Last

• Jump to page: