winaa
Member

197 Likes

Page 8 of 14 First 1234567891011121314 Last

• Jump to page:

1. 
   davetapson liked post by winaa On thread : Engineering shop to mill Stock extensions

   Workshop innovation has spacers on this page (https://www.workshopinnovation.co.nz/products.asp?cat=178)

   Liked On: 20-02-2020, 10:30 AM

2. 
   northdude liked post by winaa On thread : Short Barrel Syndrome.

   Rifle barrels the only time a guy gets to show off that his is shorter than yours. :ORLY:

   Liked On: 15-02-2020, 10:18 AM

3. 
   Moa Hunter liked post by winaa On thread : Short Barrel Syndrome.

   Rifle barrels the only time a guy gets to show off that his is shorter than yours. :ORLY:

   Liked On: 15-02-2020, 09:34 AM

4. 
   Micky Duck liked post by winaa On thread : Fast burning powder in a short 243

   Check out the pistol reloading data on the ADI website (http://www.adi-powders.com.au/pistol/243-winchester/) sample below130540

   Liked On: 14-02-2020, 06:44 PM

5. 
   Moa Hunter liked post by winaa On thread : Fast burning powder in a short 243

   Check out the pistol reloading data on the ADI website (http://www.adi-powders.com.au/pistol/243-winchester/) sample below130540

   Liked On: 13-02-2020, 10:46 PM

6. 
   Phil_H liked post by winaa On thread : Short Barrel Syndrome.

   Rifle barrels the only time a guy gets to show off that his is shorter than yours. :ORLY:

   Liked On: 10-02-2020, 10:34 AM

7. 
   Micky Duck liked post by winaa On thread : Short Barrel Syndrome.

   Rifle barrels the only time a guy gets to show off that his is shorter than yours. :ORLY:

   Liked On: 09-02-2020, 05:12 PM

8. 
   Cordite liked post by winaa On thread : Pulling projectile - neck tension?

   I have an ear plug in my "kinetic" bullet puller. Cushions the projectile well and doesn't trap a lot of powder. Just pull the ear plug when finished and clean out the remaining powder. Agree about...

   Liked On: 05-02-2020, 12:38 PM

9. 
   lee308 liked post by winaa On thread : Remington 700 from 308 to 6.5CM Criterion prefit barrel quick job report

   Hey that's awesome I have been pondering this for long time (actually 2 rifles ago) but never really took the leap. Nice write up Thanks for sharing, I may go that way myself in the future I have...

   Liked On: 04-02-2020, 07:32 PM

10. 
    blake liked post by winaa On thread : Diesel utes/suvs next under the ban hammer?

    If they ban diesel's, I'll rip out my efficient little diesel and put a dirty big V8 Petrol in it instead. It might cost me a bit but be worth it just to piss off the greenie's.

    Liked On: 30-01-2020, 07:37 PM

11. 
    Tikka7mm08 liked post by winaa On thread : Kimber Montana 308 Load Development

    Different units of pressure mate Don't quote me but is about 52000 CUP is about 60000 PSI in the 308 win. Tikka7mm08 A well know accurate load for the 308 is 41.5Gr of H4895 (ADI 2206H same...

    Liked On: 24-01-2020, 08:19 AM

12. 
    Moa Hunter liked post by winaa On thread : Subsonic projectiles, where are we at these days?

    If you had more case volume so you could give the bullet more energy then you wouldn't be subsonic any more. Kind of a silly statement really the idea of a 300 Blk-out is a small volume case so you...

    Liked On: 30-12-2019, 02:23 PM

13. 
    Bagheera liked post by winaa On thread : Subsonic projectiles, where are we at these days?

    If you had more case volume so you could give the bullet more energy then you wouldn't be subsonic any more. Kind of a silly statement really the idea of a 300 Blk-out is a small volume case so you...

    Liked On: 29-12-2019, 10:31 AM

14. 
    25 /08 IMP liked post by winaa On thread : What's everyone using to de cap brass without sizing for annealing ?

    Just spend $30.00 on a lee decaping die. Easy as saves messing with your other dies

    Liked On: 24-12-2019, 08:21 AM

15. 
    dannyb liked post by winaa On thread : What's everyone using to de cap brass without sizing for annealing ?

    Just spend $30.00 on a lee decaping die. Easy as saves messing with your other dies

    Liked On: 24-12-2019, 12:17 AM

Page 8 of 14 First 1234567891011121314 Last

• Jump to page: