Wingman
Member

2384 Likes

Page 65 of 159 First ... 155152535455565758596061626364656667686970717273747576777879115 ... Last

• Jump to page:

1. 
   veitnamcam liked post by Wingman On thread : Projectile manufacturing

   eople like myself who have hunted with Bryns bullets will agree that they work great for hunting with the advantage of a small hollow point for a better BC than the easily deformed soft point bullets.

   Liked On: 03-05-2021, 09:34 AM

2. 
   257weatherby liked post by Wingman On thread : Projectile manufacturing

   eople like myself who have hunted with Bryns bullets will agree that they work great for hunting with the advantage of a small hollow point for a better BC than the easily deformed soft point bullets.

   Liked On: 03-05-2021, 09:21 AM

3. 
   madjon_ liked post by Wingman On thread : Banned Members vs Ejected ones

   Sad... but true

   Liked On: 12-03-2021, 07:17 AM

4. 
   veitnamcam liked post by Wingman On thread : Banned Members vs Ejected ones

   Sad... but true

   Liked On: 12-03-2021, 12:36 AM

5. 
   Micky Duck liked post by Wingman On thread : 308 twist rate

   My .338 Whispers ran 1-9" twist Shilen and trueflite barrels shooting 300gr SMKs and 300gr Berger hybrids at 1040fps MV. They were still perfectly stable and grouping well with round holes at...

   Liked On: 25-01-2021, 09:28 PM

6. 
   caberslash liked post by Wingman On thread : Zastava 7.62x39 Restoration

   Dama dama Shes all finished.. although it could do with the barrel being dumped in a hot blue tank which I will have done at some stage to give it a darker more durable blue than my make shift cold...

   Liked On: 04-01-2021, 01:26 PM

7. 
   caberslash liked post by Wingman On thread : Zastava 7.62x39 Restoration

   Yes that is basically where I ended up. 130636 After loading a few 125gr TMKs and finding a load with 2207 over the chrono I found the case formed to the chamber nicely and all slop at the rear...

   Liked On: 04-01-2021, 01:22 PM

8. 
   caberslash liked post by Wingman On thread : Zastava 7.62x39 Restoration

   So the MAB barrel blank I selected is a 25" long 4140 CM 1-10" twist light Sako contour in a .308" bore diameter. The profile was a fraction lighter than the Zastava barrel but I am planning to my...

   Liked On: 04-01-2021, 01:20 PM

9. 
   caberslash liked post by Wingman On thread : Zastava 7.62x39 Restoration

   Before I got started on the new 7.62x39 barrel I had a .22 grendel itch I had to scratch.. I had a very short trueflite 1-8" twist .223Rem take off barrel that I wanted to test the .22 Grendel...

   Liked On: 04-01-2021, 01:18 PM

10. 
    L461 liked post by Wingman On thread : Attempting a new .224 wildcat

    I have had a few private messages with questions in regards to this build and how the barrel life etc was holding up so I figured Id do an update here too. The barrel is still going strong...

    Liked On: 01-01-2021, 05:59 AM

11. 
    Bol Tackshin liked post by Wingman On thread : San mai style skinning knife build

    The acid etch removed all the loose scale and cleaned out all the rust in the forging pits which was not the look I wanted so I decided to re rust the blade now it was etched so the pits would look...

    Liked On: 29-12-2020, 10:02 PM

12. 
    mimms2 liked post by Wingman On thread : San mai style skinning knife build

    I had a crack at a skinning knife a couple of weeks back just to fill in a quiet week. I used to make knives when I was a kid, raiding my uncles workshop for random off cuts of stainless steel etc....

    Liked On: 29-12-2020, 07:55 PM

13. 
    Tikka7mm08 liked post by Wingman On thread : San mai style skinning knife build

    The acid etch removed all the loose scale and cleaned out all the rust in the forging pits which was not the look I wanted so I decided to re rust the blade now it was etched so the pits would look...

    Liked On: 29-12-2020, 04:38 PM

14. 
    Kiwi Sapper liked post by Wingman On thread : San mai style skinning knife build

    I had a crack at a skinning knife a couple of weeks back just to fill in a quiet week. I used to make knives when I was a kid, raiding my uncles workshop for random off cuts of stainless steel etc....

    Liked On: 29-12-2020, 09:51 AM

15. 
    Tahr liked post by Wingman On thread : San mai style skinning knife build

    The acid etch removed all the loose scale and cleaned out all the rust in the forging pits which was not the look I wanted so I decided to re rust the blade now it was etched so the pits would look...

    Liked On: 29-12-2020, 05:43 AM

Page 65 of 159 First ... 155152535455565758596061626364656667686970717273747576777879115 ... Last

• Jump to page: