Yesmate
Member

142 Likes

Page 2 of 10 First 12345678910 Last

• Jump to page:

1. 
   Yesmate liked post by TeRei On thread : Handheld Thermal for the Bush

   Is that why you use a 80ltr pack to carry all your goodies. LOL. You must split the pack... 40ltr for projectiles [39 different makes ] and 40 ltrs for hunting goodies. Too much.*

   Liked On: 26-12-2024, 01:22 PM

2. 
   Yesmate liked post by Friwi On thread : Tikka T3x Lite in .30-06, questions about barrel length

   Well I would say, start by killing gongs at 600 on the first shot. That would be good exercise.

   Liked On: 22-12-2024, 08:43 AM

3. 
   Yesmate liked post by caberslash On thread : 7mm mag to a 6.5prc?

   Reloading speeds are equivalent to talking about appendage size. Everyone is up for a boast until an accurate measuring device comes out. Hornady have said that some people claim 6.5 CM loads that...

   Liked On: 04-12-2024, 04:57 PM

4. 
   Yesmate liked post by 25/08 IMP On thread : 7mm mag to a 6.5prc?

   Never tried the 156 but 143 or 147 2818 from a 18 " and 2860 from 20" both Tikka Sent from my CPH2531 using Tapatalk

   Liked On: 01-12-2024, 02:14 PM

5. 
   Yesmate liked post by Mooseman On thread : Factory ammo speed variations

   It’s not only Hornady ammo as I test some 95 gr Ballistic Silver tips a short while back in my 243. From four shots I got an average speed of 2826 fps and the spread was 156.4 fps, measured on a...

   Liked On: 01-11-2024, 08:35 PM

6. 
   Yesmate liked post by 308 On thread : Crackdown in Wairarapa

   Yes I've complained to the IPCA before and it is a total waste of time - utterly toothless I've got some fuckwit that stole 40k worth of tools out of my storage garage and he is still paying me...

   Liked On: 08-10-2024, 09:00 PM

7. 
   Yesmate liked post by Husky1600#2 On thread : Couple of relevant job adverts - Geraldine and Wellington

   The guiding position will only be when they have clients, so late Feb - May. Possibly decent gaps between clients, $35 per hour starts to look pretty average. High fence guiding, not everybody's cup...

   Liked On: 02-10-2024, 03:53 PM

8. 
   Yesmate liked post by matto1234 On thread : Napier marlin

   Get a sst subscription with the marine chart overlays and keep an eye on it, you might get lucky again this season

   Liked On: 29-09-2024, 08:53 AM

9. 
   Yesmate liked post by blip On thread : Bush rifles

   Fuk that dreaded name popped up. Bush pig is such a stupid name for a rifle. Back in the day it was just called a carbine

   Liked On: 19-09-2024, 08:34 AM

10. 
    Yesmate liked post by Gordo On thread : Hunting fitness

    Just find a decent hill locally, put a 20kg pack on your back and walk up and down it for an hour a four or five times a week.

    Liked On: 13-09-2024, 08:30 AM

11. 
    Yesmate liked post by Micky Duck On thread : 6.5 creedmoor reviews??????

    If you currently sport a manbun go with the costsmore. You said only below 400 so .243 all day long would get my vote between the two choices.

    Liked On: 08-09-2024, 09:40 AM

12. 
    Yesmate liked post by tim37 On thread : last deer, maybe ?

    decided to take Mazy the dog out for one last hunt, she now has bad arthritis in both front wrist joints and a dodgy hip as well. loaded the truck up Thursday night and headed up the Awatere...

    Liked On: 31-08-2024, 10:16 PM

13. 
    Yesmate liked post by Ted6.5 On thread : 6.5prc loads

    57.2g of Super performance is giving me 2963 out of a new T3x, federal 210 primers. Work up carefully though.

    Liked On: 06-08-2024, 08:49 AM

14. 
    Yesmate liked post by 25/08 IMP On thread : 6.5prc loads

    I load Hodgdon Superperformance and 142. Nosler ablr at about 2960fps Sent from my CPH2531 using Tapatalk

    Liked On: 06-08-2024, 08:49 AM

15. 
    Yesmate liked post by 7mmwsm On thread : Advice Needed: Choosing Caliber for Open Tops Hunting

    It's got that look about it alright. That 223 must be good. That hole isn't anywhere near the vitals.

    Liked On: 03-07-2024, 07:29 PM

Page 2 of 10 First 12345678910 Last

• Jump to page: