zimmer
Member

2540 Likes

Page 30 of 170 First ... 161718192021222324252627282930313233343536373839404142434480130 ... Last

• Jump to page:

1. 
   shananah liked post by zimmer On thread : Primer question

   How do you know :-)

   Liked On: 19-07-2023, 01:28 AM

2. 
   6x47 liked post by zimmer On thread : Bore sight Lazer way off when rifle is zeroed

   They are bloody useless. I've always eyeball bore sighted and can get on to the target at 100yds with first shot. Although No good names left has nailed the issue with them. If you have one, roll it...

   Liked On: 18-07-2023, 07:43 PM

3. 
   Marty Henry liked post by zimmer On thread : Bore sight Lazer way off when rifle is zeroed

   The next thing to learn is once you have a couple of shots on the target, and if the shots are a wee ways from your aiming mark, position your crosshair on your aiming mark, and without moving the...

   Liked On: 18-07-2023, 06:51 PM

4. 
   Micky Duck liked post by zimmer On thread : First Aid Training and Article

   The cost of defibrillators has come way down. Consideration for one at home? I've seen various changes of ratio over the years. I think at my last refresher they said don't get hung up on it as in...

   Liked On: 18-07-2023, 06:26 PM

5. 
   30.06king liked post by zimmer On thread : Bore sight Lazer way off when rifle is zeroed

   The next thing to learn is once you have a couple of shots on the target, and if the shots are a wee ways from your aiming mark, position your crosshair on your aiming mark, and without moving the...

   Liked On: 18-07-2023, 04:14 PM

6. 
   Micky Duck liked post by zimmer On thread : Bore sight Lazer way off when rifle is zeroed

   The next thing to learn is once you have a couple of shots on the target, and if the shots are a wee ways from your aiming mark, position your crosshair on your aiming mark, and without moving the...

   Liked On: 18-07-2023, 03:56 PM

7. 
   Eat Meater liked post by zimmer On thread : Bore sight Lazer way off when rifle is zeroed

   The next thing to learn is once you have a couple of shots on the target, and if the shots are a wee ways from your aiming mark, position your crosshair on your aiming mark, and without moving the...

   Liked On: 18-07-2023, 03:55 PM

8. 
   Micky Duck liked post by zimmer On thread : Bore sight Lazer way off when rifle is zeroed

   They are bloody useless. I've always eyeball bore sighted and can get on to the target at 100yds with first shot. Although No good names left has nailed the issue with them. If you have one, roll it...

   Liked On: 18-07-2023, 03:52 PM

9. 
   blip liked post by zimmer On thread : Use LPP as a substitution

   The rod is just a small machine screw I had lying around. Being threaded it hangs on with the epoxy used. IIRC I drilled a hole thru the primer so that the open end goes into the pocket same as it...

   Liked On: 15-07-2023, 09:00 PM

10. 
    blip liked post by zimmer On thread : Use LPP as a substitution

    Here are my gauges. The wooden handled one I made using an old RWS LR primer. Any primer pocket that the gauge goes into over 1/2 its depth is on its way out. The other 2 are go/no gauges from...

    Liked On: 15-07-2023, 08:11 PM

11. 
    10-Ring liked post by zimmer On thread : CCI BR4 vs CCI 400 primer’s

    BR4s are not hard so much as they have a thicker cup than others. Back in the days of converting 308 range rifles (no change to firing pin hole in bolt) to 6MM BR for F Class it was quite common to...

    Liked On: 15-07-2023, 01:27 AM

12. 
    Micky Duck liked post by zimmer On thread : "Karhu" A.K.A "Finnish Bear" 30-06 load developement

    When I had a magnetospeed I always made sure I did the attached and un attached at the same range session. Also observed some loads that grouped better with the MS attached. Stands to reason as the...

    Liked On: 13-07-2023, 10:03 PM

13. 
    Micky Duck liked post by zimmer On thread : Use LPP as a substitution

    They are also dimensionally shorter. 228568

    Liked On: 10-07-2023, 08:14 PM

14. 
    Husky1600#2 liked post by zimmer On thread : Use LPP as a substitution

    Used them in my 22 Hornets for years and the Hornet should be a bit hotter than most pistol cartridges. I still wear safety glasses though with one of my Hornets as it's an older design with not...

    Liked On: 10-07-2023, 06:59 PM

15. 
    Puffin liked post by zimmer On thread : CCI BR4 vs CCI 400 primer’s

    BR4s are not hard so much as they have a thicker cup than others. Back in the days of converting 308 range rifles (no change to firing pin hole in bolt) to 6MM BR for F Class it was quite common to...

    Liked On: 10-07-2023, 04:15 PM

Page 30 of 170 First ... 161718192021222324252627282930313233343536373839404142434480130 ... Last

• Jump to page: