Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

Ammo Direct ZeroPak


User Tag List

+ Reply to Thread
Results 1 to 15 of 39
Like Tree15Likes

Thread: RCBS Dies... Problem?

Hybrid View

  1. #1
    Almost literate. veitnamcam's Avatar
    Join Date
    Dec 2011
    Location
    Nelson
    Posts
    25,071
    Quote Originally Posted by Ryan_Songhurst View Post
    What do you man by wind down VC? Wind the die down further? I have it setup so that shellholder stops on bottom of the die as per instructions with the dies... They seem to be sizing to spec well I just cant understand why I nearly have to rip my press off the bench especially when they are not stretching much during firing so the die isnt actually doing much sizing really.
    You are hitting the case holder while on the sizing stroke with a case being sized?!?

    First ascertain where the case is stopping you chambering it, if it is at the mouth all good trim, if it is at the shoulder your die needs to go down, die setting instructions are shit....dont set to touch the case holder set to match your rifles chamber lenght/headspace.

    If it is tight on the shoulder the die needs to go down, if it is kissing the shell holder WHILE SIZING the case you need to remove some of the die from the bottom.
    presses stretch and kissing the holder with no case can be miles of with a case.
    "Hunting and fishing" fucking over licenced firearms owners since ages ago.

    308Win One chambering to rule them all.

  2. #2
    Codswallop Gibo's Avatar
    Join Date
    Feb 2013
    Location
    The Hill
    Posts
    23,570
    Quote Originally Posted by veitnamcam View Post
    You are hitting the case holder while on the sizing stroke with a case being sized?!?

    First ascertain where the case is stopping you chambering it, if it is at the mouth all good trim, if it is at the shoulder your die needs to go down, die setting instructions are shit....dont set to touch the case holder set to match your rifles chamber lenght/headspace.

    If it is tight on the shoulder the die needs to go down, if it is kissing the shell holder WHILE SIZING the case you need to remove some of the die from the bottom.
    presses stretch and kissing the holder with no case can be miles of with a case.
    I think he can chamber it and the measurements stack up its just tight as on the way out of the die

  3. #3
    Almost literate. veitnamcam's Avatar
    Join Date
    Dec 2011
    Location
    Nelson
    Posts
    25,071
    Quote Originally Posted by Gibo View Post
    I think he can chamber it and the measurements stack up its just tight as on the way out of the die
    He said excessive resistance closing the bolt.

    Sent from my SM-G800Y using Tapatalk
    "Hunting and fishing" fucking over licenced firearms owners since ages ago.

    308Win One chambering to rule them all.

  4. #4
    Codswallop Gibo's Avatar
    Join Date
    Feb 2013
    Location
    The Hill
    Posts
    23,570
    He did, my bad As you were mate ha ha ha

 

 

Similar Threads

  1. FS 300 win mag RCBS dies
    By HUNTY in forum Projectile and Factory Ammo Exchange
    Replies: 1
    Last Post: 27-11-2017, 09:41 PM
  2. RCBS Chargemaster 1500 problem??
    By Baz in forum Reloading and Ballistics
    Replies: 75
    Last Post: 10-10-2012, 09:49 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!