Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

DPT Terminator


User Tag List

+ Reply to Thread
Page 2 of 5 FirstFirst 12345 LastLast
Results 16 to 30 of 70
Like Tree55Likes

Thread: See separation?

  1. #16
    Member
    Join Date
    May 2019
    Location
    Rotorua
    Posts
    180
    Unlike steel, brass does not harden with rapid cooling, it makes no difference if it is dropped in water or left to air cool. The only way to harden brass is by working it as in sizing it.

    A few questions.
    How do you anneal them?
    Do you clean your brass and if so how and what additives do you use?

  2. #17
    Member
    Join Date
    Jan 2018
    Location
    New Zealand
    Posts
    796
    Never seen that happen after a only a couple firings.
    One thing I notice is that the carbon on the case appears to continue past the cartridge neck and onto the shoulder. To me this would indicate that the case is getting sized too much, pushing the cartridge headspace back too far; allowing gas past the neck and onto the shoulder. (or the headspace on the rifle is too long).
    If you have headspace comparators then try measuring a sized case vs a fired case. Id bet the headspace on the sized case is too shot. (meaning you should back your full length die out - or try neck sizing only)
    Tahr, nor-west, GWH and 1 others like this.

  3. #18
    Member Mathias's Avatar
    Join Date
    Oct 2015
    Location
    Canterbury, home of the big Rakaia Red Stag
    Posts
    4,513
    @Tahr if you know someone with an AMP machine, it could be possible to revive this brass with an accurate anneal. I have no proof with that this would work, but it makes logical sense.

  4. #19
    Member
    Join Date
    May 2012
    Location
    Sydney
    Posts
    1,632
    I have had that sort of cracking of the neck in .257 AI cases. It occurs when I do not anneal at all. Usually get a split down the neck and neck base.

    As stated above quenching in water does not impact annealing.

    My guess is not annealling far enough down the shoulder.
    outlander likes this.

  5. #20
    R93
    R93 is offline
    Member R93's Avatar
    Join Date
    Feb 2012
    Location
    Westland NZ
    Posts
    16,102
    Quote Originally Posted by 7mmsaum View Post
    That’s not annealing, an instant cool is Tempering which will make the brass harder/brittle
    Dunno if it is temepering/hardening but I never rapidly cool my brass.

    Odd to do that after a couple firing so my guess is over annealing and a host of other possible issues.



    Sent from my SM-T510 using Tapatalk
    Do what ya want! Ya will anyway.

  6. #21
    Member
    Join Date
    Aug 2017
    Location
    King Country
    Posts
    2,458
    Quote Originally Posted by 7mmsaum View Post
    That’s not annealing, an instant cool is Tempering which will make the brass harder/brittle
    Thank the stars that you're wrong. Almost had me pulling bullets there.

  7. #22
    Member outdoorlad's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch
    Posts
    3,010
    @Tahr do you anneal below the shoulder?
    Shut up, get out & start pushing!

  8. #23
    Member
    Join Date
    Dec 2011
    Location
    NI
    Posts
    12,764
    Quote Originally Posted by outdoorlad View Post
    @Tahr do you anneal below the shoulder?
    No. I pretty much just do the neck and some shoulder.

  9. #24
    Member
    Join Date
    Dec 2011
    Location
    NI
    Posts
    12,764
    I "anneal" using my gas stove (single burner camping thing) and heat the neck holding the base of the case and twirling it. When I feel the heat in my fingers I dunk the case in water.

  10. #25
    Member chainsaw's Avatar
    Join Date
    Jul 2014
    Location
    Norf
    Posts
    5,771
    My guess is under rather than over annealing
    outlander and Tech like this.

  11. #26
    Member
    Join Date
    May 2019
    Location
    Rotorua
    Posts
    180
    @Tahr I would suggest that your cases aren't being annealed enough. Unless you have hands of steel there is no way that you can get the necks hot enough and still hold onto the case base. At one point I touched the base of a 6.5-284 case straight out of my AMP annealer and it instantly burnt my finger tip.
    GWH and outlander like this.

  12. #27
    R93
    R93 is offline
    Member R93's Avatar
    Join Date
    Feb 2012
    Location
    Westland NZ
    Posts
    16,102
    If it is under annealed, it is pretty shit brass to do work harden within a couple firings to cause that seperation.
    It has to be a combination of things.
    Even before the annealing craze took on you could get 5 or 6 loads out of a warm load case with most brands of brass and I don't recall seening the neck separate like those above.



    Sent from my SM-G975F using Tapatalk
    Do what ya want! Ya will anyway.

  13. #28
    Member
    Join Date
    Mar 2012
    Location
    New Zealand
    Posts
    578
    Not far enough annealing past shoulder, about 5mm needed otherwise you had a hard brass to soft brass junction at neck and shoulder junction which is most likely the highest stretching/stress region on the cartridge when fired and causing case not expand uniformly in this region.

    black stuff - just carbon as stated earlier, can darken more with gas annealing

    Rapid cooling of brass is safe as houses and does not harden it.

    One can tell if you over annealed brass with gas, first you can see the flame slightly change colour as the surface zinc in the brass burns out of the copper, also the more than usual shinny tin look to brass once annealed - not the usual annealed colour. Anyway I have fired over annealed brass as fouler shots before range shooting and never had a case separate nor any other problems apart from maybe a dented shoulder when seating projectile (but they still fire form out and case reharden with use)
    R93, Moa Hunter and outlander like this.

  14. #29
    Member zimmer's Avatar
    Join Date
    Oct 2012
    Location
    Waikato
    Posts
    4,986
    Have these cases been heck turned?

  15. #30
    Member
    Join Date
    Jul 2017
    Location
    Hawkes bay
    Posts
    903
    I've been getting split necks upon 1st firing of my norma brass, maybe 1 in 3. 300 saum necked down. 62grains of 2213sc with a 140vld . Real mild, accurate load. I wouldnt have thought they would need annealing or anything from new? Any reason why this would be happening?

 

 

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!