Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

Ammo Direct Alpine


User Tag List

+ Reply to Thread
Results 1 to 12 of 12
Like Tree2Likes
  • 2 Post By veitnamcam

Thread: Untrimmed??

  1. #1
    Member geezejonesy's Avatar
    Join Date
    Dec 2011
    Location
    near stratford
    Posts
    1,407

    Untrimmed??

    Was loading sum 223 loads and this happened to case im guessin the cases where not trimmed to correct length .am i correct ?? Or what else may it be ?

    Sent from my GT-I9100T using Tapatalk 2
    Attached Images Attached Images  
    BURN BABY BURN
    Rule 1: Treat every firearm as loaded Rule 2: Always point firearms in a safe direction Rule 3: Load a firearm only when ready to fire Rule 4: Identify your target beyond all doubt Rule 5: Check your firing zone
    Rule 6: Store firearms and ammunition safely Rule 7: Avoid alcohol and drugs when handling firearms

  2. #2
    Member
    Join Date
    Mar 2012
    Location
    Hastings
    Posts
    2,650
    Called lubing.

  3. #3
    Tread carefully in the suck... ishoot10s's Avatar
    Join Date
    May 2012
    Location
    NW of the true capital...
    Posts
    1,903
    Did they go far enough into the die to de-prime? I think that's more like the spud that goes into the neck is a bit large, maybe dirty, and it's happening well before the case is fully into the die. I think if it was case length, then the bulge would be into the case, not out of it, because the die wall will not let the case bulge out.

    Ray.
    10MRT shooters do it 60 times, in two directions and at two speeds.

  4. #4
    Member geezejonesy's Avatar
    Join Date
    Dec 2011
    Location
    near stratford
    Posts
    1,407

    Re: Untrimmed??

    I had them deprimed ok . It was when seatin the projectile . ive pulled them .

    Sent from my GT-I9100T using Tapatalk 2
    BURN BABY BURN
    Rule 1: Treat every firearm as loaded Rule 2: Always point firearms in a safe direction Rule 3: Load a firearm only when ready to fire Rule 4: Identify your target beyond all doubt Rule 5: Check your firing zone
    Rule 6: Store firearms and ammunition safely Rule 7: Avoid alcohol and drugs when handling firearms

  5. #5
    Almost literate. veitnamcam's Avatar
    Join Date
    Dec 2011
    Location
    Nelson
    Posts
    24,972
    Die set to low and trying to roll crimp case mouth?
    Trim all cases to same lenght, wind seater die down till touches case then back up half turn
    P38 and kimjon like this.
    "Hunting and fishing" fucking over licenced firearms owners since ages ago.

    308Win One chambering to rule them all.

  6. #6
    Member geezejonesy's Avatar
    Join Date
    Dec 2011
    Location
    near stratford
    Posts
    1,407

    Re: Untrimmed??

    Cheers

    Sent from my GT-I9100T using Tapatalk 2
    BURN BABY BURN
    Rule 1: Treat every firearm as loaded Rule 2: Always point firearms in a safe direction Rule 3: Load a firearm only when ready to fire Rule 4: Identify your target beyond all doubt Rule 5: Check your firing zone
    Rule 6: Store firearms and ammunition safely Rule 7: Avoid alcohol and drugs when handling firearms

  7. #7
    AB Precision
    Join Date
    Dec 2011
    Location
    Nelson
    Posts
    2,209
    If done when seating you need to chanfer the mouth its just picking up on the projectile an squishing the neck........................................but you also need to trim the shell on the bottom has a ring around it near the end because its to long in the chamber

    my 20c

  8. #8
    Member cambo's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch
    Posts
    2,154
    This page is interesting to look at.....

    diagnosing problems
    Life is natures way of keeping meat fresh

  9. #9
    Member redbang's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch
    Posts
    682
    Quote Originally Posted by cambo View Post
    This page is interesting to look at.....

    diagnosing problems
    Cool info in there Cambo, good post

  10. #10
    Member gadgetman's Avatar
    Join Date
    Jan 2012
    Location
    Christchurch
    Posts
    17,981
    I managed to get the same result by setting a bullet pulling collet too low. just the slight movement of getting the handle moving was enough, on a press that is meant to not have any downward movement at the top of the stroke.

  11. #11
    P38
    P38 is offline
    Member P38's Avatar
    Join Date
    Dec 2011
    Location
    Hastings
    Posts
    5,692
    Quote Originally Posted by veitnamcam View Post
    Die set to low and trying to roll crimp case mouth?
    Trim all cases to same lenght, wind seater die down till touches case then back up half turn
    Your onto it VC.

    Done that exact thing myself a couple of times.

  12. #12
    dog chaser distant stalker's Avatar
    Join Date
    Dec 2011
    Location
    Chch
    Posts
    2,013
    yep seating die set too low. running 308 through a 7mm08 collect die is another way to achieve the same effect (neck size from 308 to7mm, collect dies will work once fired- not that you asked about these cals)

 

 

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!