Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

Terminator Alpine


User Tag List

Like Tree268Likes

Thread: AR Thread

  1. #391
    Member cambo's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch
    Posts
    2,154
    Anyone used any Barnaul ammo through their AR's?

    I have used it in a BA and it wasn't the best, to put it kindly. Had quite a few cases jam.

    Just wondering 'cause it's cheap and steel cased (so I don't have to look for my good brass in the tussock and snow grass).
    Life is natures way of keeping meat fresh

  2. #392
    Member Beavis's Avatar
    Join Date
    Dec 2011
    Location
    Taupo
    Posts
    4,891
    Functions 100% but shoots like poo

  3. #393
    Member Beavis's Avatar
    Join Date
    Dec 2011
    Location
    Taupo
    Posts
    4,891
    3-4MOA+

  4. #394
    Member cambo's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch
    Posts
    2,154
    Cheers Beavis.
    I'll try some and see if it cycles Ok in my R15.
    Not too worried about accuracy at this stage.
    Life is natures way of keeping meat fresh

  5. #395
    Member dogmatix's Avatar
    Join Date
    Dec 2011
    Location
    Northern Gaul (Pukekohe)
    Posts
    6,045
    Cambo, you might be better off with the steel cased Hornady ammo.
    Welcome to Sako club.

  6. #396
    Member cambo's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch
    Posts
    2,154
    I would if I could dogmatix. lol
    I have used it in the AR before and it is good.........BUT......Supplies are very low anywhere.
    Life is natures way of keeping meat fresh

  7. #397
    Member
    Join Date
    Dec 2011
    Location
    South Canterbury
    Posts
    651
    Barnaul voids any and all warrantees - and I actually think I am not joking come to think of it - even manufacturers know its crap and if you run it, it voids warrantee - which is normally the reverse as some/most state you must only run factory thru there rifles.

  8. #398
    Member dogmatix's Avatar
    Join Date
    Dec 2011
    Location
    Northern Gaul (Pukekohe)
    Posts
    6,045
    Quote Originally Posted by muzr257 View Post
    Barnaul voids any and all warrantees - and I actually think I am not joking come to think of it - even manufacturers know its crap and if you run it, it voids warrantee - which is normally the reverse as some/most state you must only run factory thru there rifles.
    I'm sure it was the same with Wolf ammo.
    Welcome to Sako club.

  9. #399
    Member cambo's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch
    Posts
    2,154
    Cheers Muzr
    I won't touch the crap then.
    Life is natures way of keeping meat fresh

  10. #400
    By Popular Demand gimp's Avatar
    Join Date
    Dec 2011
    Location
    The Big H
    Posts
    9,512
    Wolf is an importer. They sell a lot of relabelled ammunition, some of which is made by Barnaul. Barnaul is a bi-metal jacket and will wear your barrel a lot faster. I will dig up a link later about it where it's tested in 3 rifles, compared to Federal M193 loads.

    Buy some of the BVAC stuff from Reloaders, or some Belmont.

  11. #401
    Member cambo's Avatar
    Join Date
    Dec 2011
    Location
    Christchurch
    Posts
    2,154
    I'm needing to get some rails to put on my R15.
    Anyone got any, or know of a good supplier?

    Just need to be able to mount a few important accessories.
    Isn't grown up lego great
    Life is natures way of keeping meat fresh

  12. #402
    Member
    Join Date
    Jun 2013
    Location
    Christchurch
    Posts
    919
    Hi

    Was wondering if anybody knew where i would be able to get a 10-12" barrell for my bushmaster. Looking at starting a new upper build project with a small lightweight rifle in mind. Have looked at the states but no way in hell can i get anything i want out. Any help or advice would be appreciated.

    cheers

  13. #403
    Ejected
    Join Date
    Dec 2012
    Location
    HBC, NORTH of Auckland
    Posts
    5,249
    Longer barrel cut down?

  14. #404
    Member Beavis's Avatar
    Join Date
    Dec 2011
    Location
    Taupo
    Posts
    4,891
    What is ur current set up? If it is a 16" carbine you should be able to trim the tube to the appropriate length, it might require the gas port to be opened a little, due to the decrease in dwell time. If u have a rifle length tube it will require lathe work after the cut down to get the right profile for the gas block. I wouldn't trust local smiths to do this properly.

  15. #405
    Guest
    Join Date
    Dec 2011
    Location
    Kapiti
    Posts
    549
    We will have 10.5 barrels next week
    Dan likes this.

 

 

Similar Threads

  1. what thread
    By madjon_ in forum Reloading and Ballistics
    Replies: 7
    Last Post: 04-10-2018, 08:27 AM
  2. Thread titles
    By veitnamcam in forum Questions, Comments, Suggestions, Testing.
    Replies: 4
    Last Post: 30-08-2012, 01:35 PM

Tags for this Thread

View Tag Cloud

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!