Thread: Gun Porn, show off your new toys

Originally Posted by foxhound

nice rig their, haydendev. my nea-15 dmr also runs a timney, with the samson evo 10'' handguards, currently in A cat format. hows the groups at 100m ive had good results with fiocchi 69grain loads, sierra matchking loads.

havent done much testing so far, got about 1.3 inch 5 rounds group with hornady 55gr #2266 at 100m.
had a few barnaul 55gr and 62gr projs, to try to see if i could get away with some super cheap ones, and they were getting about 3.5-4.5inch, haha, so will stick with the hornadys in the mean time and do some more load development, see if i can get any smaller, and will try some heavier projectiles when i can get my hands on some, and some time to do some more testing.
gun will mainly be 3gun rifle, so the cheaper the better as will have plenty put thru it, but certainly would like better than 4 moa accuracy would be preferable haha

She is a bit of a beast at the moment and I have a lot of work to do to get her shooting again but hopefully she will turn into a classy medium bore once again.

Anybody with some 9.5x57 brass or components or advice, please get in touch.

This has been up and running for a while now. I was going to hold off from photos until I painted the stock, which I still haven't done but will at some point. Does anyone know of a good textured paint for a stock? Big thanks to Abe for the barrel fitting, chambering and suppressor and to Leathel for help with bedding and use of his mill for the stock inletting.

Specs are:
Howa Short action
MAB 1:8 22" #5 .260 REM
Hi-Tech Specialties Stock
Sightron SIII 3.5-10 Mil/Mil
EGW 20MOA base and Leupold QRW 30mm Low rings
Bipod is VersaPod copy and Vektor Maskin spigot
Tui_man Suppressor

Very nice!



Sent from my iPhone using Tapatalk. So please forgive my sausage fingers!!!

Looking Good

looks great Normie,dont paint the stock it looks good how it is.

Originally Posted by Dan

New 'toys'?

This is my latest rifle build. Anyone know how to flute wooden barrels?

Attachment 8838

100mm grinder with a sanding disk, only solution

Scatter gun?

Iz that the new defender?

Sent from my GT-I9300 using Tapatalk 2

Originally Posted by CreepingDeath

Iz that the new defender?

Sent from my GT-I9300 using Tapatalk 2

Remington 870 Tactical with a cheap side sadle for shell holder. Plan is to adda police spec trigger, upgrade the ejectors if I need to, add some sort of sight, and shoot a fuck ton of slugs, and shit through it. Might get a second longer barrel for foul, or clays if Ic an be arsed.

New 308

Come on bro give us the spiel.

Sent from my GT-I9300 using Tapatalk 2

RRA LAR8 that's had handguard slotted and reanodised, Timney trigger and brake fitted.
I don't rate RRA Ar15s personally but the big boys arnt generic mil spec stuff. All propriety thus very different in build quality.
Takes SLR mags which is the reason I went with it as opposed to DPMS, REM, CMMG etc which all interchange parts wise, but arse for mags and ESP big mags.
Lose parts availability for mag availability which is acceptable to me in this case.
Will try and get another upper and bolt and will build a 7SAUM upper also.

I want one sooo bad. Whats the weight. Anything you can do to get them skinny? Obviously lose ten inches of barrel but anything else?

Sent from my GT-I9300 using Tapatalk 2

Nice one there Spanners, here goes a few of NEA 14.5 with custom handguard and waitaki can fitted as of just then. pretty wrapped with how guard came up, just what I was after. Gave the trigger a lick over too havnt put the scales on it but its lost about ten tonnes and a heap of creep and graunching so im excited to get it out tomorrow!!