Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

Alpine Darkness


User Tag List

+ Reply to Thread
Page 2 of 2 FirstFirst 12
Results 16 to 29 of 29
Like Tree9Likes

Thread: Removing heavy carbon fouling (suppressor)

Hybrid View

  1. #1
    Member
    Join Date
    Jun 2013
    Location
    Middle Earth
    Posts
    4,553
    Stand you rifle up vertical against a wall before the 6 o'clock news. Put a good dose of boretech c4 on the crow so it soaks in. Have diner, dessert , watch movie, have sex then wipe the muzzle with a towel then it should be all clean( talking about the rifle muzzle here !). If not re apply c4 and leave over night and should be all clean in the morning.
    Gibo, PERRISCICABA and Sideshow like this.

  2. #2
    Member
    Join Date
    Jun 2013
    Location
    Middle Earth
    Posts
    4,553
    Quote Originally Posted by Friwi View Post
    Stand you rifle up vertical against a wall before the 6 o'clock news. Put a good dose of boretech c4 on the crow so it soaks in. Have diner, dessert , watch movie, have sex then wipe the muzzle with a towel then it should be all clean( talking about the rifle muzzle here !). If not re apply c4 and leave over night and should be all clean in the morning.
    Your rifle. And crown not crow

  3. #3
    northdude
    Guest
    probably not the best thing to do i use hoppes 9 and 1000 1200 wet and dry just go easy tho it works for me

  4. #4
    Member dogmatix's Avatar
    Join Date
    Dec 2011
    Location
    Northern Gaul (Pukekohe)
    Posts
    6,223
    I use the neck of a 30 cal case the clean the carbon off the end of the muzzle.
    Done in 10-15 seconds and no harm to the crown, as its brass on steel.
    Welcome to Sako club.

  5. #5
    Member Driverman's Avatar
    Join Date
    Apr 2013
    Location
    HUTT VALLEY
    Posts
    461
    Quote Originally Posted by dogmatix View Post
    I use the neck of a 30 cal case the clean the carbon off the end of the muzzle.
    Done in 10-15 seconds and no harm to the crown, as its brass on steel.
    Even water can wear down steel eventually

  6. #6
    Member dogmatix's Avatar
    Join Date
    Dec 2011
    Location
    Northern Gaul (Pukekohe)
    Posts
    6,223
    Quote Originally Posted by Driverman View Post
    Even water can wear down steel eventually
    We'll all be dead by the time that happens.
    Gibo likes this.
    Welcome to Sako club.

  7. #7
    Member
    Join Date
    Dec 2011
    Location
    Hawera
    Posts
    1,098
    autosol

  8. #8
    Member Chur Bay's Avatar
    Join Date
    Jan 2016
    Location
    Cambridge
    Posts
    1,708
    Scotchbrite works good. Just add solvent of choice.

  9. #9
    Member
    Join Date
    Feb 2012
    Location
    Rapa
    Posts
    1,061
    KG1 Carbon remover also works very well.

  10. #10
    Hen
    Hen is offline
    Member
    Join Date
    Mar 2016
    Location
    Christchurch
    Posts
    150
    I had a a light but stubborn dusting of carbon on my muzzle also, just used very fine steel wool that i use to clean my brass, a couple of spins on the crown and it looks like new, i added kroil to the wool as well.

  11. #11
    Member dogmatix's Avatar
    Join Date
    Dec 2011
    Location
    Northern Gaul (Pukekohe)
    Posts
    6,223
    Sorry, I was referring to a poor threading job from the mentioned smith.
    Welcome to Sako club.

  12. #12
    Member Puffin's Avatar
    Join Date
    May 2012
    Location
    Porirua
    Posts
    1,037
    Quote Originally Posted by Hen View Post
    ....used very fine steel wool that i use to clean my brass, a couple of spins on the crown and it looks like new
    Quote Originally Posted by Chur Bay View Post
    Scotchbrite works good. Just add solvent of choice.
    The absolute symmetry in a rotational sense of the cut of the crown around the bore centre (not barrel OD) plays a critical part in overall rifle accuracy. Abrasives that have the capability to remove steel - as in the two mentioned above - are probably best avoided regardless of the care taken. It is problematic enough that the removed carbon then forms an abrasive paste with the working solvent, and is the reason for commonly choosing to pass a bore brush one way only down the bore.

  13. #13
    Member Chur Bay's Avatar
    Join Date
    Jan 2016
    Location
    Cambridge
    Posts
    1,708
    Shit. I just figured it was plastic so it would be softer than steel.
    You learn something every day

  14. #14
    Member Chur Bay's Avatar
    Join Date
    Jan 2016
    Location
    Cambridge
    Posts
    1,708
    Shit. I just figured it was plastic so it would be softer than steel.
    You learn something every day

 

 

Similar Threads

  1. Suppressors and carbon fouling - what's your got to fix ?
    By chainsaw in forum Reloading and Ballistics
    Replies: 41
    Last Post: 17-01-2016, 04:00 PM
  2. DPT SUPPRESSOR FOR HEAVY BARREL RIFLES
    By PERRISCICABA in forum Firearms, Optics and Accessories
    Replies: 9
    Last Post: 05-07-2014, 02:10 AM
  3. Hightec Stock and 700 Rem bull barrel with heavy suppressor
    By 257weatherby in forum Firearms, Optics and Accessories
    Replies: 3
    Last Post: 02-05-2014, 08:52 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!