Thread: 30-06ai 60 series custom landcruiser build

Couple more hours spent on the cruiser this afternoon, got the last patch panel shaped, cut out and tacked into place.
Tidied up a couple of welds on the side panels I did last visit. Will finish pulse welding the last panel in then there's a heap of grinding and sanding to tidy up my average welding
I also noticed a couple pin holes I the roof along where it was chopped, so they well need some attention next visit too. Then the last panel work before prep and paint will be to weld up the bolt holes where the factory flares used to be. Making good progress every visit, so I'm happy with that.

Fully welded bottom patch....definitely needs a tidy up with the grinder but another step in the right direction

No pics today, but spent the day getting the pin holes in the roof welded up (prick of a job as it was thin).
Then got all the bolt holes where the flares would have bolted to the front guards welded up.
Good progress, next trip will be lots of sanding so I can finally start spraying the roboliner inside and out.
Was very grateful to have a more experienced mate help with welding the roof as I may have ended up with a sunroof or cabriolet if I did it

Hopefully get some sanding done in the next week or 2

I can see its a long project, good stuff Danny

Spent some more time on the truck today, ground off a heap of sloppy welds slapped on a heap of filter (most of which will be sanded off).
More good progress, next trip will sand back the filler and check for any low points, then it's on to paint prep
Will also include some pics of the guards now the flare holes have been welded up too.

Picked up a 6" air sander today, what a handy bit of gear, made quick work of removing most of the filler, had to finish a few bits by hand but overall happy with progres. I have a bit more asthetic stuff to tidy up with the grinder around the bottom of the cab but that's not a big job. Next chance I get a day off and the weather isn't shit It's getting trailered to the certification guys in Christchurch for a progress check. Once that's done it'll be all hands on deck for paint prep

No pics today but I took a quick 20sec video and loaded it up on YouTube link below.

https://youtu.be/Cao_YiD4oN4?si=ylMKPi5hZChKeQ3E

Paint is a bit wet still hence it looks patchy, just chucked it on to protect the bare metal from rusting.

Spent a day working working on the cruiser after a long break. I have been busy with work but scored a couple mid week days off
Got the last welding done to seal up the back of the cab, fitted the seats and rails back in, etch primed any bare metal. She's ready to go see the cert guys for sign off on the ute cab chop structure before the whole thing gets a link roboliner (like raptor coat but for men).
Then I can get on to putting it all back together and actually getting it running took a bunch of pics I'll load em up shortly





















Yup looks a little rough still, but once it's been signed off for the structural mods (cab chop, seat mounts, body lift and extended shakles). Then I have to strip seats back out, prep for paint and paint the whole truck inside and out with Roboliner. Big step in the right direction.

Nice. Be interesting to see what the requirements are for cert for a chop down to a single cab nowadays, last time I had anything to do with this it was mid 2000's and a Safari LWB getting shortened down to a single cab ute. The back half had a tree lean on it (gently) and it basically wasn't worth repairing the body so insurance wrote it off. The difference between buy-back of the insurance outfit and their payout made the conversion almost free...

Originally Posted by No.3

Nice. Be interesting to see what the requirements are for cert for a chop down to a single cab nowadays, last time I had anything to do with this it was mid 2000's and a Safari LWB getting shortened down to a single cab ute. The back half had a tree lean on it (gently) and it basically wasn't worth repairing the body so insurance wrote it off. The difference between buy-back of the insurance outfit and their payout made the conversion almost free...

The top half of the back of the cab is made from the rear hatch cut and shut to the body and fully seam welded, the bottom half is 3mm sheet steel, with a heavy c section running the entire width of the cab about halfway way up what's left of the rearwheel arches. I am confident it will be very strong. Even if my welds are ugly they are solid. Once the welds and structure are given the all clear I'll run a bead of urethane over them just to tidy things up asthetically. There is definitely no pin holes but even if there is I have treated with crc rust converter and a few decent coats of crc etch primer. The urethane will be just an extra bit of insurance and make it look neater.

Once cert guys have inspected it I will have a better idea if it's strong enough, there's plenty of scope to add more reinforcement if needed but I think it'll be OK.

Ahh that makes a lot of sense, the Safari was a single cab with two rear doors that were locked permanently as the tray was preventing them from being opened. Basically, the rear ring (pillar sill and roof curve) were ground off and welded back onto the body with a bit of a provision for the chassis rails and a revised mounting setup. If I have it right, the rear mounts were welded into place in front of the rear sill and the mounts were cut off the rear of the chassis and made into bolt on ones...