Welcome guest, is this your first visit? Create Account now to join.
  • Login:

Welcome to the NZ Hunting and Shooting Forums.

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed.

Terminator Night Vision NZ


User Tag List

+ Reply to Thread
Page 2 of 2 FirstFirst 12
Results 16 to 22 of 22
Like Tree6Likes

Thread: Suppressor changing point of impact by inches

  1. #16
    Sending it Gibo's Avatar
    Join Date
    Feb 2013
    Location
    The Hill
    Posts
    23,480
    My old MAE 2 tonne suppressor used to cause a 8" poi change from on to off @100

  2. #17
    Member
    Join Date
    Feb 2017
    Location
    Jafa land
    Posts
    5,441
    Quote Originally Posted by DPT View Post
    We give the bushes clearance, about 0.05mm over size, open it up a little so its not touching the barrel.
    Sweet. I have a pipe reamer at work I'll use. Or get the engineers to use the lathe.

    Sent from my TA-1024 using Tapatalk

  3. #18
    Member Marty Henry's Avatar
    Join Date
    Oct 2014
    Location
    Tararua
    Posts
    7,088
    I recall Browning used to offer a barrel tuner called the BOSS basically a weight that you used to slide up or down the barrel to change the point of impact, any weight or pressure on the barrel will change the poi. Just compare shooting a few rounds normally then resting the barrel on the sandbag and see where the rounds go.

  4. #19
    Member
    Join Date
    Feb 2017
    Location
    Jafa land
    Posts
    5,441
    Quote Originally Posted by Marty Henry View Post
    I recall Browning used to offer a barrel tuner called the BOSS basically a weight that you used to slide up or down the barrel to change the point of impact, any weight or pressure on the barrel will change the poi. Just compare shooting a few rounds normally then resting the barrel on the sandbag and see where the rounds go.
    I've seen rubber rings out on the range.

    I texted my mate and he said that it was inside the barrel not outside centered

    Sent from my TA-1024 using Tapatalk

  5. #20
    Member
    Join Date
    Mar 2012
    Location
    Waikato
    Posts
    2,095
    Truly 6" at 25 yd ?
    Thats too much for barrel flip. Something else must be loose.

    My 7mm08 had 10cm change at 100m with suppressor on. Then it went crazy 20 .. 30cm out worse with supp off than on ...
    Turned out a scope base screw had come loose and the suppressor was affecting how much unpredictable movement occurred in the mounting. Tightened that one screw and it went back to behaving itself.

    Is your gun shooting well with the suppressor off ?

  6. #21
    Member
    Join Date
    Feb 2017
    Location
    Jafa land
    Posts
    5,441
    Quote Originally Posted by Bagheera View Post
    Truly 6" at 25 yd ?
    Thats too much for barrel flip. Something else must be loose.

    My 7mm08 had 10cm change at 100m with suppressor on. Then it went crazy 20 .. 30cm out worse with supp off than on ...
    Turned out a scope base screw had come loose and the suppressor was affecting how much unpredictable movement occurred in the mounting. Tightened that one screw and it went back to behaving itself.

    Is your gun shooting well with the suppressor off ?
    That's what the fella helping me reckoned. 4-6 inches.

    It's got iron sights.

    Yeah it did a good group for someone who's never shot irons before. Will try against sometime and see if it helps



    Sent from my TA-1024 using Tapatalk

  7. #22
    Member
    Join Date
    Dec 2018
    Location
    Dunedin
    Posts
    42
    I've never experienced a difference of poi with or without a suppressor over 600 mtrs except one time when the thread in the suppressor was very slightly off center. I noticed a tiny indent on the muzzle of the suppressor where the projectile was just brushing against.
    Russian 22. likes this.

 

 

Similar Threads

  1. Film 20: Point of Impact
    By gimp in forum Shooting
    Replies: 9
    Last Post: 15-05-2015, 08:48 AM
  2. just for intrest sake will these two 223 ammos shoot to the same point of impact
    By rambo-6mmrem in forum Firearms, Optics and Accessories
    Replies: 14
    Last Post: 05-05-2015, 12:58 PM
  3. F&*$ You, Inches!
    By Dougie in forum Shooting
    Replies: 28
    Last Post: 24-11-2014, 04:14 PM
  4. cutting a 16 inch carbine barrel to 12 inches
    By Bill999 in forum Firearms, Optics and Accessories
    Replies: 42
    Last Post: 31-03-2013, 10:44 PM
  5. Changes in the impact point
    By phillipgr in forum Shooting
    Replies: 50
    Last Post: 18-03-2013, 10:33 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
Welcome to NZ Hunting and Shooting Forums! We see you're new here, or arn't logged in. Create an account, and Login for full access including our FREE BUY and SELL section Register NOW!!